Loacting Wires + ECU ****HELP
#2
Scooby Regular
Join Date: Jul 2000
Location: Lancashire
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
I have these on my PC at home, unfortunately I'm not going to be there for 3 days
There is a STi V3/4 pinout on the Ravensblade site, power/gnd/road speed input/rpm feed to dash are the same as a UK car.
When you say speed I presume you mean road speed from the gearbox pickup? This is fed to both the ECU and the dash clocks in parallel from the gearbox sensor, unlike the engine speed where the sensor signal goes to the ECU which in turn drives the tacho.
Andrew...
There is a STi V3/4 pinout on the Ravensblade site, power/gnd/road speed input/rpm feed to dash are the same as a UK car.
When you say speed I presume you mean road speed from the gearbox pickup? This is fed to both the ECU and the dash clocks in parallel from the gearbox sensor, unlike the engine speed where the sensor signal goes to the ECU which in turn drives the tacho.
Andrew...
#3
Andrew,
I belive that is the one...I am trying to connect my Blitz Power ID Meter, and have been told i need to tap into that wire....
Have not had much luck in finding this info, so will drop a post if i do locate before hand...
Where is the ecu located?
Thanks
Sam
I belive that is the one...I am trying to connect my Blitz Power ID Meter, and have been told i need to tap into that wire....
Have not had much luck in finding this info, so will drop a post if i do locate before hand...
Where is the ecu located?
Thanks
Sam
#5
Scooby Regular
Join Date: Jul 2000
Location: Lancashire
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
Just found some notes on my PC at work:
B135 (16pin connector) pin 3 = Vehicle Speed Input
B136 (22pin connector) pins 1&2 = Main Relay +12v
B136 (22pin connector) pin 12&13 = Ground
Andrew...
B135 (16pin connector) pin 3 = Vehicle Speed Input
B136 (22pin connector) pins 1&2 = Main Relay +12v
B136 (22pin connector) pin 12&13 = Ground
Andrew...
#6
Andrew,
Thanks for the info...I will atempt to locate the wires this this evening after work...
Is it ok to assume, after i locate the ecu, there will be marking for me to locate the cable labbled B13* for the 3 cables? Or is it little more complicated then that?
Sam
Thanks for the info...I will atempt to locate the wires this this evening after work...
Is it ok to assume, after i locate the ecu, there will be marking for me to locate the cable labbled B13* for the 3 cables? Or is it little more complicated then that?
Sam
#7
Scooby Regular
Join Date: Jul 2000
Location: Lancashire
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
There are 3 yellow connectors going into the ECU, B135/6/7. They are all 2 row with 16/22/12 pins respectively so you can't mix them up.
The power and gnd connectors are next to each other (as its a 2 row 22 pin connector, 12 is below 1 and 13 is below 2).
The diagrams I have at home make it much clearer than I can in words.
Andrew...
The power and gnd connectors are next to each other (as its a 2 row 22 pin connector, 12 is below 1 and 13 is below 2).
The diagrams I have at home make it much clearer than I can in words.
Andrew...
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM