TOYOTA MR2 Turbo torque settings
#2
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
I have a Toyota Repair manual for the 3S-GE, 3S-GTE and 5S-FE. I used to have a 1990 MR2 Turbo, what did you specifically want to know? I purchased this book a few years ago from a main agent, It did take me some time to get it though.
#3
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Apr 2003
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
thanks for the reply,
basically i have given a mechanic a full bottom end to rebuild,
and hes struggling finding the settings for replacing crank, big ends etc, but i suppose hes going to need everything eventually to put it all back together, head bolts etc, whatever you could dig out would be greatly appreciated,
thanks again, Andy
basically i have given a mechanic a full bottom end to rebuild,
and hes struggling finding the settings for replacing crank, big ends etc, but i suppose hes going to need everything eventually to put it all back together, head bolts etc, whatever you could dig out would be greatly appreciated,
thanks again, Andy
#4
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
Ok, starting from the crank here's a few:-
Main Bearing Caps(Crank to Block) - 600kg-cm (43ft-lb, 59Nm)
Connecting Rod Caps(Conrods to crank) - 680 kg-cm (49ft-lb, 67Nm)
Inner Oil Seal Retainer - 6 Bolts 95kg-cm (82 in-lb, 9.3Nm)
Flywheel - 8 Bolts (Apply Loctite or equiv) 1100kg-cm (80ft-lb, 108Nm
Drive Plate - 850kg-cm (61ft-lb, 83Nm)
Knock Sensor - 450kg-cm (33ft-lb, 44Nm)
Rear End Plate - 95kg-cm (82ft-lb, 9.3Nm)
Note-when installing Main bearing shells No3's is 23.0mm width whereas the rest are 19.2mm
Theres a few, let us know if you need anymore
Cheers
[Edited by Delboy2 - 11/30/2003 2:02:44 AM]
Main Bearing Caps(Crank to Block) - 600kg-cm (43ft-lb, 59Nm)
Connecting Rod Caps(Conrods to crank) - 680 kg-cm (49ft-lb, 67Nm)
Inner Oil Seal Retainer - 6 Bolts 95kg-cm (82 in-lb, 9.3Nm)
Flywheel - 8 Bolts (Apply Loctite or equiv) 1100kg-cm (80ft-lb, 108Nm
Drive Plate - 850kg-cm (61ft-lb, 83Nm)
Knock Sensor - 450kg-cm (33ft-lb, 44Nm)
Rear End Plate - 95kg-cm (82ft-lb, 9.3Nm)
Note-when installing Main bearing shells No3's is 23.0mm width whereas the rest are 19.2mm
Theres a few, let us know if you need anymore
Cheers
[Edited by Delboy2 - 11/30/2003 2:02:44 AM]
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM
Scott@ScoobySpares
Full Cars Breaking For Spares
7
14 December 2015 08:16 AM
johnnybon
Wheels And Tyres For Sale
7
25 September 2015 07:49 AM