Notices
General Technical
Sponsored by:
Sponsored by: CARiD

why wont it go in

Thread Tools
 
Search this Thread
 
Old Feb 24, 2001 | 08:16 PM
  #1  
DAZ HALL's Avatar
DAZ HALL
Thread Starter
Scooby Newbie
 
Joined: Feb 2001
Posts: 20
Likes: 0
Post

I have just bought my first subaru (96,UK 4door) . When i put some petrol in it , the pump kept cutting off ,so it took me ages to fill up.I tried a different petrol station incase it was a faulty pump,but that was the same .Is there a fault on my car ,or are they a bit tempromental.
Reply
Old Feb 24, 2001 | 08:42 PM
  #2  
bob's Avatar
bob
Scooby Regular
 
Joined: Nov 1998
Posts: 1,391
Likes: 0
From: Bristol
Post

You have the nozzle to far in. Try pulling it out a bit until it sits in a grove on the bottom of the nozzle. Some owners also rotate the nozzel 45%. But I always withdraw a little and give it full flow
Reply
Old Feb 24, 2001 | 09:02 PM
  #3  
DAZ HALL's Avatar
DAZ HALL
Thread Starter
Scooby Newbie
 
Joined: Feb 2001
Posts: 20
Likes: 0
Post

CHEERS ,BOB will try that .Only had the car since tuesday and been working all week , so hoping to have a good run tommorow .
Reply
Old Feb 24, 2001 | 09:12 PM
  #4  
Luke's Avatar
Luke
BANNED
 
Joined: Jan 2001
Posts: 9,644
Likes: 0
From: In my own little world
Post

Try "KY JELLY" Not sure if withdrawing it a bit will help.And as for rotating it 45 degrees, that is going to hurt

[This message has been edited by Luke (edited 24 February 2001).]
Reply
Old Feb 24, 2001 | 09:36 PM
  #5  
Dick White's Avatar
Dick White
Scooby Regular
 
Joined: Mar 2000
Posts: 119
Likes: 0
Exclamation

Yep...turn the nozzle so its at an angle. i find that mines best when held at 90% to the left of the normal position ....oeer !

Reply
Old Feb 25, 2001 | 01:29 PM
  #6  
Moss's Avatar
Moss
Scooby Regular
 
Joined: Sep 2000
Posts: 165
Likes: 0
Post

I find nozzle upside down is best!
Reply
Old Feb 26, 2001 | 01:05 PM
  #7  
Dave T-S's Avatar
Dave T-S
Scooby Regular
 
Joined: Aug 2000
Posts: 8,897
Likes: 4
From: Newmarket Suffolk
Wink

"A Muppeting we will go......."
Reply
Old Feb 26, 2001 | 03:22 PM
  #9  
The Woodman's Avatar
The Woodman
Scooby Regular
 
Joined: Jan 2001
Posts: 38
Likes: 0
Wink

You're all quite clearly missing out the foreplay before inserting the nozzle!
Reply
Old Feb 26, 2001 | 04:05 PM
  #10  
ndouglass's Avatar
ndouglass
Scooby Regular
 
Joined: Sep 2001
Posts: 312
Likes: 0
Post

That's right.. You've gotta open the flap nice & wide then twist & turn the cap until it comes loose then you put in your nozzle...

Without doing that first you'll get your shoes wet..

Reply




All times are GMT +1. The time now is 07:02 AM.