I have decided that I need to release some money I have invested in the car so it has to go. All parts available. I am located near manchester in the OL2 postcode area.
The following prices are for collection. I may post some of the smaller items for cost.



Exterior styling


Brand new from Subaru Front wings £300
alloy bonnet in primer with red scoop and side grills £90

Number plate "R55OOB" £650


Wheels and Brakes


Brembo 2 piston rear calipers with new pads £250


Engine and management
2.0 litre closed deck block (stroked to 2.1)
EJ257 crank, Auris pistons, Brian Crower con rods
Standard STi v3 heads
Cosworth head gasgets
Cosworth super high tensile head bolts
Cosworth sump baffle plate
Cosworth kevlar cam belt
ARP case bolts
Cosworth 12mm oil pump
Cosworth timing belt guide
Kent adjustable vernier camshaft pulleys £4000

The engine has done 4500 miles. 1000 of them were running in and another 1000 were at only 0.8 bar of boost.

RCM (ex gobstopper) catch tank with return to sump £140
Custom head breather ports £35 if bought with the catch can £25


Alkatek ECU with AL and LC activated and comes with the air inlet temp sensor. reduced to £550
phase 1.5 Custom engine loom with newage coil pack conversion and 4 newage coilpacks £100

Induction and Exhaust

Revolution 3” catback £180



Fueling

Bosch 044 external fuel pump
Billet fuel rails
Braided PTFE lined fuel hose (parallel) with AN fittings
Fuel distribution block
SX fuel filter
Swirl pot
Billet fuel filter
£350 for the lot
Walbro in-tank fuel pump £30
SX fuel pressure regulator with gauge £70
Lateral performance modified yellow 900cc Injectors £250

Interior


Pioneer DEH P9600 head unit (available now) £25
V4 STi clocks £40
Front and rear seats in good condition £60
Door cards front and rear £20
Any other standard trim just ask


Have a look at my project thread for pictures https://www.scoobynet.com/projects-4...ect-500-a.html If you want current pictures of anything just ask.

 

Hi mate.it probably won't work/fit but can you pm me a pic of the custom induction shield please

 

Have you still got carbon boot lid and what make is the 3 port boost solenoid? Cheers

 

I will take the RCM/K&N large cone filter if you can post please

 

 

I can post for £5 if you cover PayPal fees. PayPal address is shmerman69@yahoo.com please.

 

The boot lid was crap so it went back. The 3 port is a denso from memory but will double check.

 

How much for this if still available ????

 

£40 mate

 

Hello mate, just had a look through the project thread regarding removal of ABS. What parts have you got left to accommodate this? I've just got my fusespulled at the moment to keep it off, it's bloody dangerous! Anyway, I want it all out so if be interested in the parts.

 

Pm'd mate

 

Hi, I have the T pieces needed to connect the front lines together and the rear lines together. I also have the adjustable bias valve so that you can balance the breaking once all the ABS system and oem bias has been removed.
cheers
Mike

 

How much would you be looking for those bits?

 

£18 delivered pal

 

Sounds alright to me! I'll PM ya

 

RCM cone filter recieved with many thanks

 

Payment sent earlier for the ABS delete stuff

 

whats the best price on the bonnet mate?

what colour is it

and where abouts are you?

cheers

 

I have 2 bonnets. a reddish blue steel one.

An an alloy one in primer. The primer has flaked off in a couple of places so might need doing again.

Alloy one £130 comes with red scoop and side vents as these havent been stripped

 

as it says in the advert im in Oldham

 

What colour are the door cards I need rear ones ? Cheers

 

Hello mate your inbox is full and I can't send you any more PMs -I have paid for the 3 port boost solenoid mate and asked if you could post it to my Subaru Specialist - his details are in the note on the Paypal receipt you will receive

 

Parts arrived today, thanks!

 

My parts also arrived today as promised - top man, cheers mate

 

parts recieved , all good , many thanks .

 

I know you've received a deposit but how much were you after for MD321V turbo?

Inbox me if you like

 

Have you got any pictures of the 3" Revolution cat back exhaust ?

Also if this is off a classic saloon,do you know if it will fit a classic wagon ?

 

Pictures of the Walbro fuel pump and the front seats?

 

The olie cooler, where is it placed?
Are interested

 

Can I have a pic of the rear unknown brand strut brace please