not boosting over 1.1 bar
#1
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Feb 2006
Location: www.slowboy-racing.co.uk
Posts: 439
Likes: 0
Received 0 Likes
on
0 Posts
not boosting over 1.1 bar
Hi All,
I'm currently having boost issues with my car. The car is mapped using syvecs to 1.5 bar. However it won't boost more then 1.1 bar at the most. The cal switch is set to the 1.5 bar map.I have tested with other maps such as 1.2 etc.but all show up as 1.1 bar.
I have replaced all the piping to the boost solonoid and turbo etc. I have even tried another 3 port but still get same issue.
Can anyone advise how i can do some diagnosis using syvecs to help me determine what the issue could be.
Any help will be appreciated. I have tried to contact my mapper but have not had any luck getting in contact with them.
Any help will be appreciated
djquest
I'm currently having boost issues with my car. The car is mapped using syvecs to 1.5 bar. However it won't boost more then 1.1 bar at the most. The cal switch is set to the 1.5 bar map.I have tested with other maps such as 1.2 etc.but all show up as 1.1 bar.
I have replaced all the piping to the boost solonoid and turbo etc. I have even tried another 3 port but still get same issue.
Can anyone advise how i can do some diagnosis using syvecs to help me determine what the issue could be.
Any help will be appreciated. I have tried to contact my mapper but have not had any luck getting in contact with them.
Any help will be appreciated
djquest
#3
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Feb 2006
Location: www.slowboy-racing.co.uk
Posts: 439
Likes: 0
Received 0 Likes
on
0 Posts
I removed all fmic pipe work and checked fmic aswel. Replaced clamps and boost hoses. I wondering if I could see in the logs for syvec what boost I was hitting to help me determine at least my solonoid and map sensor are working correctly.
#4
Scooby Regular
iTrader: (7)
Hi there
Did you downloaded SSuite from Syvecs if not please,install on your laptop,connect ECU with RJ45 cable(normal Ethernet cable for broadband),on your laptop select SData and there select Data -> Read Data/Auto read
If you want log more parameters,which doesn't show at logs the,with connected ECU please select SCfg,then select Device -> Get config,then will appear window and you can select which one parameter you want log in which frequency
Which parameters,means what have look on this
http://www.syvecs.com/forum/viewtopic.php?f=4&t=356
If you have all sensors installed,you should be able log data for oil temp/pressure,fuel pressure,ACT(air charge temperature),wideband,EGT etc
And what boost gauge are you using or you have fitted Toucan or Bluetooth module?
Not sure where are you located,but if you are somewhere near London,I'm happy to come and help you with this
Thanks,Jura
Did you downloaded SSuite from Syvecs if not please,install on your laptop,connect ECU with RJ45 cable(normal Ethernet cable for broadband),on your laptop select SData and there select Data -> Read Data/Auto read
If you want log more parameters,which doesn't show at logs the,with connected ECU please select SCfg,then select Device -> Get config,then will appear window and you can select which one parameter you want log in which frequency
Which parameters,means what have look on this
http://www.syvecs.com/forum/viewtopic.php?f=4&t=356
If you have all sensors installed,you should be able log data for oil temp/pressure,fuel pressure,ACT(air charge temperature),wideband,EGT etc
And what boost gauge are you using or you have fitted Toucan or Bluetooth module?
Not sure where are you located,but if you are somewhere near London,I'm happy to come and help you with this
Thanks,Jura
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM