i just got 311/290 at powerstation yesterday on my 2001 wrx with a vf34. thats with full de-cat, ported headers and up pipe, sti intercooler, 3 port boost solenoid, a 255lph fuel pump and an ecutek remap, it didnt need the 550cc sti injectors as it was getting plenty of fuel. its also got all the whiteline handling bits, eibach springs and its had a 4 wheel alignment. so i was just wondering what mod i should get next. thanks in advance for any advice.

 

im starting to think this whole chasing figures thing is crap and wont give u much pleasure, just leaves wanting more and more power, id say save your money and buy a different car

 

Message from your gearbox. No more torque please!!

Subject to your brakes being ok- have you upgraded to fast road pads? I'd leave it at that personally, sounds like you've got a nicely specified road car there! You're getting to a stage where you could spend quite a lot mmore, but the law of diminishing returns will begin to apply!

Ns04

 

Good advice NSO4

 

sure mine was the same! just worded differently

 

brakes are fine, been upgraded to ebc turbo groove disks with ferodo pads. can anyone recomend any nice front splitters.

 

Get a new gearbox, ready to replace yours! then get a FMIC, then take apart the engine and start to change parts to lighten it. i.e flywheell, clutch, con rods etc!

Willsy

 

By an STI then mod that.

 

Sounds like there is headroom for more power on your current spec.

Did the mapper ask what you had in mind or was there something else stopping you getting more from it?

What boost is it mapped to? Did it it target boost on the rollers? Mapped on RR or road mapped?

 

if it was my day to day driver I wouldn't go much further with out spending big money

if it was for weekends this is where I went from a simular stag to you

http://bbs.scoobynet.co.uk/showthread.php?t=490419

edited to add

I know it will not last at this spec but hopefully keep me going untill I get a built engine \ gear box together if it dosn't last im no worse off as I don't need the car ( don't tell the misses I said that )

 

Dont say that Rich FFS

you will curse it! fill your pint pot half full and think of Fuzz's car runing 400 ish on uk internals for so long.

*but saave a bit every month just in case*

 

it was mapped on the rollers. i think he said it was mapped to 1.2bar. does that sound about right?

 

its prob mapped at 1.25 if it was done at power station, i got 310.5 in my classic my 00 with a vf35 and sti8 intercooler,full decat ect. ive got loads of other mods but they,re mainly safety mods so i would mind having my boost turned up a bit next time if possible. is anyone else running a vf35 or 34? what boost you running and what power you got?? sorry to hyjack the thread.

 

I'm interested in this as I have the same upgrades as you except vf35 and non-ported headers and getting 309/311 at 1.3 bar max boost. I've also had a cracking tax rebate and want to spend some dosh.

All suggestions welcome...

 

what car is yours and what turbo you running?

 

heres my spec on my my00

tek 3
vf35 turbo
ported and wrapped headers
greddy up pipe
sti8 intercooler
large scoop
custom undertray and air splitter
walbro pump
parallel fuel rails
ported throttle body
inlet manifold insulators
hks pannel filter
airbox mod with extra cold air feed on the side
prf7b spark plugs
ic spray set up with 3 nozles
3 inch open neck downpipe (wrapped)
decat resonated centre
scooby sport 4 1/2in jap style backbox
stage 1 fast road clutch

it got 310.5 bhp 371.8 mn at 1.25 bar boost

i might see if i can run 1.3 bar on my next remap tweek

 

vF35
decat H&S up and down pipes
STI pinks
STI8 intercooler and scoop
Walbro 255 pump
Green panel filter
PPP exhaust
Tek 3 to taste.

MY03 WRX wagon.

 

rentonone, I have the same spec aprat from std up pipe, K&N filter and 2 1/2 exhaust (std centre pipe) - 333BHP and 310 lb/ft. Boost is 1.4 - 1.3 bar IIRC.

F

 

sounds good mate, different mappers must have there own ideas of safety with boost levels cause mine is mapped to 1.25 bar.

 

Where do u people get your money from for these mods , please tell me cos i want sum

ignore me im just poor after taxing my scooby

 

im usually skint myself mate, i just save up and buy bits at a time and fit it myself to save on labour charges.