3 port subaru oil catch cans
#272
Scooby Regular
iTrader: (10)
Join Date: Oct 2007
Location: Up North
Posts: 625
Likes: 0
Received 0 Likes
on
0 Posts
How much clearance is there between the drain plug and the bolt hole Chris? Doesn't look as if there's very much, is there enough to fit an M8/M10 bolt head in there? Without catching?
#273
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
I don't at the moment, we will be making our own range of fittings this year,. so if you havent fitted i will gladly supply foc
the m10 will sit flush in the counterbore ,. there is a picture in one of the earlier post s
the m10 will sit flush in the counterbore ,. there is a picture in one of the earlier post s
#276
Scooby Regular
I just had a quick glance in my engine bay arriving home from work.
Behind the battery and fuse box, where the secondary air pump bits used to be, there is a small ledge with a hole in that could potentially be a mounting spot. It looks very tight and I cant tell until I investigate the weekend. If it is too tight, which i think it may be, there is space to install a plate using the existing hole and reposition the mounting hole away from the fusebox. The height looks very tight too, again ill have a good mooch the weekend when I have time
There may be other spots, but seeing as ive had the pump pulled out, I wanted the can to fill its place
Hawkeye sti.
If I remember in the morning ill take a pic and upload so it makes a bit more sense.
Behind the battery and fuse box, where the secondary air pump bits used to be, there is a small ledge with a hole in that could potentially be a mounting spot. It looks very tight and I cant tell until I investigate the weekend. If it is too tight, which i think it may be, there is space to install a plate using the existing hole and reposition the mounting hole away from the fusebox. The height looks very tight too, again ill have a good mooch the weekend when I have time
There may be other spots, but seeing as ive had the pump pulled out, I wanted the can to fill its place
Hawkeye sti.
If I remember in the morning ill take a pic and upload so it makes a bit more sense.
Last edited by DantheMan2605; 05 September 2013 at 08:29 PM.
#277
Scooby Regular
iTrader: (2)
Join Date: Apr 2006
Location: paisley
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
Sorry for the misunderstanding guys. I have edited the first post ,.
These DO come with pipework - but is it only Clear pvc .
If you want decent silicone (samco like) pipework then I can supply this at £10 a meter . 3 meters should be enough .
Sorry I don't have a date at the moment as we are still working on them and there is lots to be done. I have noticed other sellers selling welded cans and comparing in them to our cans. Our cans are Billet version like Mishimoto ones that retail over £200.
I am honestly doing these cans pretty much at cost and they are a bargain - you just need to hang in there with me and your get a nice product
These DO come with pipework - but is it only Clear pvc .
If you want decent silicone (samco like) pipework then I can supply this at £10 a meter . 3 meters should be enough .
Sorry I don't have a date at the moment as we are still working on them and there is lots to be done. I have noticed other sellers selling welded cans and comparing in them to our cans. Our cans are Billet version like Mishimoto ones that retail over £200.
I am honestly doing these cans pretty much at cost and they are a bargain - you just need to hang in there with me and your get a nice product
Chris
Last edited by mctwistuk; 06 September 2013 at 05:46 PM.
#281
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
guys, sorry i thought i posted info on the hoses, the clear pvc stuff isn't really up to to the job for oil, where the silicone hoses i can do at cost £10 per metre i will be able to offer 2 years warranty with . i'm not saying this to make a extra buck as it is honesty at cost,
but if you just want the pvc stuff let me know and ill get it posted
everyone else chasing orders i will come back to them asap
thanks chris
but if you just want the pvc stuff let me know and ill get it posted
everyone else chasing orders i will come back to them asap
thanks chris
#287
Scooby Regular
iTrader: (3)
So some people received theirs on the 2nd September yet 9 days later and I'm still waiting (and I guess I'm not the only one?)
I'd explained I'd made arrangements to have this, turbo, fuel reg and a load of other bits fitted this weekend, I'm now going to have to cancel that as it makes far more sense to have them done at the same time whilst there's easier access.
Last I spoke to you Friday you said it, and the pipework, would be posted imminently?
Cmon mate what's the deal?
I'd explained I'd made arrangements to have this, turbo, fuel reg and a load of other bits fitted this weekend, I'm now going to have to cancel that as it makes far more sense to have them done at the same time whilst there's easier access.
Last I spoke to you Friday you said it, and the pipework, would be posted imminently?
Cmon mate what's the deal?
Last edited by Muzza80; 11 September 2013 at 05:39 PM.
#289
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
I am sorry for the hold up,. we run out of newage fittings and Im doing my very best to get more made and sorted ... all orders were dispatched in order they was paid for so I have done it the fairest i can.
I am looking to dispatch all outstanding orders i have with me tomorrow for a friday delivery
what i have left to go is
aaron monkman
matthew goldsberry
michael charlton
murray storm
Mark Plumpton
all I can do is apologize,, if your name is not above you should have had it by now for sure ,.. please pm me if its not with you
I am looking to dispatch all outstanding orders i have with me tomorrow for a friday delivery
what i have left to go is
aaron monkman
matthew goldsberry
michael charlton
murray storm
Mark Plumpton
all I can do is apologize,, if your name is not above you should have had it by now for sure ,.. please pm me if its not with you
Last edited by CDF Racing; 11 September 2013 at 05:59 PM.
#290
Scooby Regular
iTrader: (12)
Join Date: Jun 2007
Location: Moved to the Darkside
Posts: 5,034
Likes: 0
Received 0 Likes
on
0 Posts
I am sorry for the hold up,. we run out of newage fittings and Im doing my very best to get more made and sorted ... all orders were dispatched in order they was paid for so I have done it the fairest i can.
I am looking to dispatch all outstanding orders i have with me tomorrow for a friday delivery
what i have left to go is
aaron monkman
matthew goldsberry
michael charlton
murray storm
Mark Plumpton
all I can do is apologize,, if your name is not above you should have had it by now for sure ,.. please pm me if its not with you
I am looking to dispatch all outstanding orders i have with me tomorrow for a friday delivery
what i have left to go is
aaron monkman
matthew goldsberry
michael charlton
murray storm
Mark Plumpton
all I can do is apologize,, if your name is not above you should have had it by now for sure ,.. please pm me if its not with you
#292
Scooby Regular
iTrader: (3)
On another note....
I don't want to be running the filter open inside the engine bay, I'd like to fit a 90 degree silicone pipe from that fitting at the top then join to/run another silicone pipe from there, out of the bay somewhere, perhaps through the wing.
Can you tell me diameter of the fitting at the top so I can get the correct ID silicone elbow ordered up?
Cheers!
Last edited by Muzza80; 12 September 2013 at 06:50 PM.
#293
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
That's fair enough Chris, It's just good to be in the picture then people can work around it, will look forward to receiving the can tomorrow.
On another note....
I don't want to be running the filter open inside the engine bay, I'd like to fit a 90 degree silicone pipe from that fitting at the top then join to/run another silicone pipe from there, out of the bay somewhere, perhaps through the wing.
Can you tell me diameter of the fitting at the top so I can get the correct ID silicone elbow ordered up?
Cheers!
On another note....
I don't want to be running the filter open inside the engine bay, I'd like to fit a 90 degree silicone pipe from that fitting at the top then join to/run another silicone pipe from there, out of the bay somewhere, perhaps through the wing.
Can you tell me diameter of the fitting at the top so I can get the correct ID silicone elbow ordered up?
Cheers!
12mm mate,
All outstanding orders now dispatched and will be delivered tomorrow 13/09/13
thanks chris
#298
Scooby Regular
iTrader: (11)
Join Date: Feb 2011
Location: Newcastle upon tyne
Posts: 2,750
Likes: 0
Received 0 Likes
on
0 Posts
Here it is on my Hawk , although not plumbed yet.
Easy to install with a fabricated bracket I put together in 10 mins , unscrewed the bottom of can to attach , then unscrewd the side viewing pipe , screwed can to base , & re- attached
Simple
Easy to install with a fabricated bracket I put together in 10 mins , unscrewed the bottom of can to attach , then unscrewd the side viewing pipe , screwed can to base , & re- attached
Simple