The Prodrive makeover!!
#1505
Thread Starter
Scooby Regular
iTrader: (52)
Joined: Jun 2010
Posts: 11,769
Likes: 1
From: C+K MOTORS
OK I'll let you all in on the real deal and sorry for the little joke there
It's stripped back down for a colour change and even better I'm building a new engine.
Spec will be 2.1 using mahle 2618 93mm stroker pistons with JDM big port heads and spec-c cams along with ID1000 injectors,one peice spec-c manifold and billet spec-c fuel rails,big thanks to Ty for the a selection of parts going into this new engine
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
It's stripped back down for a colour change and even better I'm building a new engine.
Spec will be 2.1 using mahle 2618 93mm stroker pistons with JDM big port heads and spec-c cams along with ID1000 injectors,one peice spec-c manifold and billet spec-c fuel rails,big thanks to Ty for the a selection of parts going into this new engine
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#1516
Thread Starter
Scooby Regular
iTrader: (52)
Joined: Jun 2010
Posts: 11,769
Likes: 1
From: C+K MOTORS
Took a road trip this morning to see a good friend and had a good chin wag but it was mainly to pick up some lovely new engine goodies for the new motor.
Massive thanks mate and it was great to see you again
New 2618 high compression Mahle stroker pistons/RCM ultra torque heads studs and Cosworth stopper gaskets will be landing early next week courtesy of Alyn at AS Perfomance who as usual go's the extra mile to make the transaction a good one,cheers mate
Parts ,79mm nitrated crank,all block seals including dowty washers plus cam seals and valve stem oil seals,basically every seal needed par the HG's.
Oh and some ACL race bearings[big and mains].
The engine will go for machine work later next week after pistons land and I find time to make the trip to Russ.
[IMG][/IMG]
[IMG][/IMG]
Massive thanks mate and it was great to see you again
New 2618 high compression Mahle stroker pistons/RCM ultra torque heads studs and Cosworth stopper gaskets will be landing early next week courtesy of Alyn at AS Perfomance who as usual go's the extra mile to make the transaction a good one,cheers mate
Parts ,79mm nitrated crank,all block seals including dowty washers plus cam seals and valve stem oil seals,basically every seal needed par the HG's.
Oh and some ACL race bearings[big and mains].
The engine will go for machine work later next week after pistons land and I find time to make the trip to Russ.
[IMG][/IMG]
[IMG][/IMG]
Last edited by prodriverules; 20 July 2013 at 09:15 PM.
#1519
Thread Starter
Scooby Regular
iTrader: (52)
Joined: Jun 2010
Posts: 11,769
Likes: 1
From: C+K MOTORS
I had hoped my manifold smoothing days were over but after deciding to change direction on the engine I now needed to smooth the spec-c one piece manifold,set about it this afternoon.
Got most of it done but run out of belt for my sander so that stopped play.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
It will over to the metal master after I'm done for a little custom love to fill the holes and make a neater dome on the top
Got most of it done but run out of belt for my sander so that stopped play.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
It will over to the metal master after I'm done for a little custom love to fill the holes and make a neater dome on the top
#1520
Scooby Senior
iTrader: (51)
Joined: Nov 2005
Posts: 20,491
Likes: 2
From: Wherever I park my car, that's my home
Looking very good mate. I'm going to start mine too next week, and then you'll have a stack of bits winging their way across to you
BTW, and chance of a touch up pot of the white you used for my wheels
BTW, and chance of a touch up pot of the white you used for my wheels
#1521
Thread Starter
Scooby Regular
iTrader: (52)
Joined: Jun 2010
Posts: 11,769
Likes: 1
From: C+K MOTORS
Cheers Jon,the last thing I wanted to be doing was another manifold for mine but I'm thinking of the bigger picture and the gains to be had
No problem on the white I'll send some back up with the parts
No problem on the white I'll send some back up with the parts
Last edited by prodriverules; 21 July 2013 at 08:28 PM.
#1529
Thread Starter
Scooby Regular
iTrader: (52)
Joined: Jun 2010
Posts: 11,769
Likes: 1
From: C+K MOTORS
Picked the manifold up from the metal master and as per he's done a stellar job of welding over the unwanted holes and flushing over the top and this time rather than tapping 1/8th ntp threads into the back of the manifold he's added weld on unions to the back of the manifold which looks awesome.
It's off to Alex at Torques UK tomorrow for a little custom love on the fuel feeds,I'll update on this once the final drawing has been made and we decide exactly what to do
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
It's off to Alex at Torques UK tomorrow for a little custom love on the fuel feeds,I'll update on this once the final drawing has been made and we decide exactly what to do
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]