Project '500-R'
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
For those who want to remove the gearbox/engine, here's the cap to remove from behind the starter motor, use a 10mm allen key socket to remove this
And using an M8 (I think) bolt, I used one holding my coilpack to the Inlet Manifold, screw into the pin inside the hole and slowly slide it out
then you can remove the clutch release fork
And using an M8 (I think) bolt, I used one holding my coilpack to the Inlet Manifold, screw into the pin inside the hole and slowly slide it out
then you can remove the clutch release fork
Joined: Nov 2003
Posts: 13,356
Likes: 58
From: in the woods...........555 Wagon Sqn
good luck with the build
Merv having come out at the other end of a project like this I'd like to offer the following advice:
Define your goals now and stick to them. Don't let what I call feature creep set in and decide to go for bigger goals. It WILL cost you thousands and delay you months possibly even a couple of years.
I started out doing a modest build and look where I ended up, 3 years later I hasten to add.
Good luck though but be prepared for some ups and downs.
There will be downs mark my words. Stick with it though as the rewards when you've ironed out the niggles that you'll inevitably have and got it running right afterwards are tremendous!!!
Define your goals now and stick to them. Don't let what I call feature creep set in and decide to go for bigger goals. It WILL cost you thousands and delay you months possibly even a couple of years.
I started out doing a modest build and look where I ended up, 3 years later I hasten to add.
Good luck though but be prepared for some ups and downs.
There will be downs mark my words. Stick with it though as the rewards when you've ironed out the niggles that you'll inevitably have and got it running right afterwards are tremendous!!!
The final bill is likely to be nearer £30k but that is doing 120%.
My moto is do it once do it right!
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Tbh the spec in my first post is set in stone for me
the 2.1 is tried and tested by myself in my old Blobeye so I know that works for me! After speaking to Martyn and Alan @ EngineTuner I've decided on the SC46 turbo as it's affordable and will put out the power I want. I need a 6 speed to handle the power too 
Everything else on the car will be cleaned and if decided it needs replacing, I'll replace it!
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Managed to get the engine out yesterday! I've got a lot of stuff to clean up in there thinking I may have to get it sprayed a some point! I'll see how it comes up after a spring clean first!
thinking I may have to get it sprayed a some point! I'll see how it comes up after a spring clean first!
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
I've removed the gearbox, prop and diff today to sell, next on the list will be to clean under the car and to Hammerite the hubs and a few other bits!
I'll also get the struts off and clean and repaint them! I'll be getting the engine bay repainted too, not whether to keep it white or go black?
I'll also get the struts off and clean and repaint them! I'll be getting the engine bay repainted too, not whether to keep it white or go black?
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
ps maybe a nice shiny White would look 
My mate and his old man have 3 Sierra Cossies between them and all have freshly painted bays and look the nuts I'll get some pics next time I see them
My mate and his old man have 3 Sierra Cossies between them and all have freshly painted bays and look the nuts
I'll get some pics next time I see them
That looks very clean and tidy,your only 1hour 50 mins from me mate,
I would be happy to paint your bay if you don't have a painter already that is
I run a mechanical/bodyshop with my father.
Jonmc's car landed with me on saturday for his respray
I would be happy to paint your bay if you don't have a painter already that is
I run a mechanical/bodyshop with my father.
Jonmc's car landed with me on saturday for his respray
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Cheers for the offer Ry, if I was closer then I would've taken you up on it it won't be getting done for a while yet but would only be able to keep it local until I can get an engine in it 
it won't be getting done for a while yet but would only be able to keep it local until I can get an engine in it
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Bit of an update, not really done much since working loads during the Summer and having crap weather on my days off! 
Managed to get my 6 speed DCCD box in today, with a slight problem. One of the holes for the front cradle mount has rusted and there's no thread there
What do you guys think, either get a nut welded onto a plate and get it welded in place or just weld the cradle into place?
I've got some of these too, once I've painted the hubs and bought new discs they will be going on.
Managed to get my 6 speed DCCD box in today, with a slight problem. One of the holes for the front cradle mount has rusted and there's no thread there
What do you guys think, either get a nut welded onto a plate and get it welded in place or just weld the cradle into place?
I've got some of these too, once I've painted the hubs and bought new discs they will be going on.
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Also I've changed the spec slightly!
Managed to source an EJ22T so I'll be going with a built 2.35 at Engine Tuner with a Blouch turbo, possibly Dominator 3.0 XT-R!
Think I need to change the title of the thread to Project 500-R
Managed to source an EJ22T so I'll be going with a built 2.35 at Engine Tuner with a Blouch turbo, possibly Dominator 3.0 XT-R!
Think I need to change the title of the thread to Project 500-R
Good luck there
Jura
If you are going for Blouch Dominator 3.0XT-R,they're available in two exhaust housing there: 8cm and 10cm.
As many people said 8cm will be have better spool,but lower top end,10cm will be have slower spool and higher top end
Jura
As many people said 8cm will be have better spool,but lower top end,10cm will be have slower spool and higher top end
Jura
I just knew you wouldn't stick to the spec once the work was under way mind you I'm no good at sticking to the script either.
Good luck with the build.
ps I wish I'd gone down the 2.0/2.1 or 2.2/2.35 route myself now.
mind you I'm no good at sticking to the script either. Good luck with the build.
ps I wish I'd gone down the 2.0/2.1 or 2.2/2.35 route myself now.
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Well the EJ22 was pretty much presented to me just gotta pay for the bits now!
Fuel swirl pot and Bosch 044 pump will be in the boot, as will the battery, covered up
Next job is to paint the hubs and get my front discs from Godspeed! Hope the weather stays dry!!
Ty, since when have I done less than what I've said lol!
just gotta pay for the bits now! Fuel swirl pot and Bosch 044 pump will be in the boot, as will the battery, covered up
Next job is to paint the hubs and get my front discs from Godspeed! Hope the weather stays dry!!
Ty, since when have I done less than what I've said lol!
Joined: Sep 2005
Posts: 19,945
Likes: 2
From: "Engineering Perfection in Essex"
Very best of luck Merv, i can only echo Dazs comments as i too am a veteran project'er LOL.
My build was essentially a forged motor using a 2.5 base and a 450/450 target to make a torquey road motor. That kinda spiralled rapidly out of control and if id known what i know now, i would have built a 2.35l from the off.
Having probably encountered alot of issues you may come across , dont hesitate to give us a bell if you get stuck..
Frayz
My build was essentially a forged motor using a 2.5 base and a 450/450 target to make a torquey road motor. That kinda spiralled rapidly out of control and if id known what i know now, i would have built a 2.35l from the off.
Having probably encountered alot of issues you may come across , dont hesitate to give us a bell if you get stuck..
Frayz
Last edited by frayz; Sep 25, 2011 at 06:40 PM.
Thread Starter
Scooby Regular
iTrader: (5)
Joined: Aug 2003
Posts: 6,517
Likes: 1
From: Mitsubishi Lancer Evolution 8 RS
Cheers Frayz
A lot of the prep work will be done myself to save some cash but all the engine work will be left in EngineTuners's more than capable hands!
I was gonna text you regarding fixin my melted wiring loom which runs in frot of the headers! How would you recommend repairing?
Merv
A lot of the prep work will be done myself to save some cash but all the engine work will be left in EngineTuners's more than capable hands!
I was gonna text you regarding fixin my melted wiring loom which runs in frot of the headers! How would you recommend repairing?
Merv
