08/09 Hatches, Stand up and show yourselves!!!
Scooby Newbie
Join Date: Feb 2013
Location: Cambridge
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Bushes
My MOT had an advisory along the lines of "various suspension bushes are shot" - is this normal for this car with under 40k miles? I've had it since 20k miles and never tracked it, just driven it fairly quick on the road. I've also noticed the suspension squeaks a bit when going slowly over speed bumps.
It's in for its service next month at the dealer, so I might ask them to have a look. Any ideas on cost, or can I do it myself? If it's similar to replacing an ARB then I can have a go.
It's in for its service next month at the dealer, so I might ask them to have a look. Any ideas on cost, or can I do it myself? If it's similar to replacing an ARB then I can have a go.
Scooby Regular
iTrader: (5)
My MOT had an advisory along the lines of "various suspension bushes are shot" - is this normal for this car with under 40k miles? I've had it since 20k miles and never tracked it, just driven it fairly quick on the road. I've also noticed the suspension squeaks a bit when going slowly over speed bumps.
It's in for its service next month at the dealer, so I might ask them to have a look. Any ideas on cost, or can I do it myself? If it's similar to replacing an ARB then I can have a go.
It's in for its service next month at the dealer, so I might ask them to have a look. Any ideas on cost, or can I do it myself? If it's similar to replacing an ARB then I can have a go.
Scooby Newbie
Join Date: Feb 2013
Location: Cambridge
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Ok sounds like I need to jack it up and have a look then. Been doing a bit of searching and it looks like you need a meaty press for some of them, or just replace the entire arm. Looks like it's probably a dealer job
Scooby Regular
iTrader: (9)
Join Date: Nov 2010
Location: Cheltenham
Posts: 1,067
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone fitted the japspeed intercooler kit. Just having mine fitted at the moment and was told the pipe work isnt a great fit and very tight. I also bought a aem induction kit to go with it but my engine builder says theres no chance of it fitting. Help/suggestions?
Scooby Regular
Has anyone fitted the japspeed intercooler kit. Just having mine fitted at the moment and was told the pipe work isnt a great fit and very tight. I also bought a aem induction kit to go with it but my engine builder says theres no chance of it fitting. Help/suggestions?
the intercooler pipe goes straight through where your airbox was so could possibly be in the way of where your aem goes (I guess the aem goes into the wing)? I had to remove my nice tidy cosworth kits housing and adapt the filter to go just into the wing.
I also was not so happy with the pipe fit so I bought some silicone hoses and made it a bit nicer!
Induction kit before FMIC.
Old pic (its not great), and all pipes are blue now!
Cosworth filter is now in the wing!
Scooby Regular
iTrader: (9)
Join Date: Nov 2010
Location: Cheltenham
Posts: 1,067
Likes: 0
Received 0 Likes
on
0 Posts
Rob had one fitted on his STI, I have one on my WRX.
the intercooler pipe goes straight through where your airbox was so could possibly be in the way of where your aem goes (I guess the aem goes into the wing)? I had to remove my nice tidy cosworth kits housing and adapt the filter to go just into the wing.
I also was not so happy with the pipe fit so I bought some silicone hoses and made it a bit nicer!
Induction kit before FMIC.
Old pic (its not great), and all pipes are blue now!
Cosworth filter is now in the wing!
the intercooler pipe goes straight through where your airbox was so could possibly be in the way of where your aem goes (I guess the aem goes into the wing)? I had to remove my nice tidy cosworth kits housing and adapt the filter to go just into the wing.
I also was not so happy with the pipe fit so I bought some silicone hoses and made it a bit nicer!
Induction kit before FMIC.
Old pic (its not great), and all pipes are blue now!
Cosworth filter is now in the wing!
Cheers mate just spoken to Rob and seen a few pictures. Yes its an inner wing one!
Cheers mate them photos help with how you modded it etc
Scooby Regular
Hi all, been away for a while, pretty much lost interest in car forums as a whole so took a break away from it. I did manage to get some stuff done on the car though.
Takata Harnesses. Always wanted a pair, got them at a relative bargain so thought why not.
My latest bit, carbon intakes from APR Performance. Bought from the U.S. as even with postage and Import Duty, cheaper than buying than buying them here. I know Chargespeed make something similar but I prefer the look of the APR version.
Thanks to IWSTI I found a handy guide for taking the bumper off. 16 trim rivets plus guide clamps on the wings to hold it on, was fiddly taking it off, was an PITA putting it back on!
The fog light covers and side vents removed and a quick clean prior to new buts going on.
About 3 hours later they were all done. The intakes weren't so much the problem, it was the CF side vents, fit like a glove on a foot. Out came the Dremel to shave away excess fibreglass on the back and many test fits later. The tape is there as the Sikaflex was still setting.
Next up is a trip upto Revolution for the wheels and tyres, Eibach lowering springs and geometry set up then the next day to AET Motorsport for Hyperflow Induction kit, full Milltek, RCM sump baffle kit and a remap.
Takata Harnesses. Always wanted a pair, got them at a relative bargain so thought why not.
My latest bit, carbon intakes from APR Performance. Bought from the U.S. as even with postage and Import Duty, cheaper than buying than buying them here. I know Chargespeed make something similar but I prefer the look of the APR version.
Thanks to IWSTI I found a handy guide for taking the bumper off. 16 trim rivets plus guide clamps on the wings to hold it on, was fiddly taking it off, was an PITA putting it back on!
The fog light covers and side vents removed and a quick clean prior to new buts going on.
About 3 hours later they were all done. The intakes weren't so much the problem, it was the CF side vents, fit like a glove on a foot. Out came the Dremel to shave away excess fibreglass on the back and many test fits later. The tape is there as the Sikaflex was still setting.
Next up is a trip upto Revolution for the wheels and tyres, Eibach lowering springs and geometry set up then the next day to AET Motorsport for Hyperflow Induction kit, full Milltek, RCM sump baffle kit and a remap.
Scooby Senior
nice, you should of fitted some hella tones while you had the bumper off
Scooby Newbie
Join Date: Dec 2014
Location: Belgium - Eeklo
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
@ Clyne,
Any reason why you are keeping your stock intake plenum and not switching over to an STI one ?
I have an 08 WRX myself and I'd love to change it over to the red STI one, but can't seem to find much comments on that.
Any reason why you are keeping your stock intake plenum and not switching over to an STI one ?
I have an 08 WRX myself and I'd love to change it over to the red STI one, but can't seem to find much comments on that.
Scooby Regular
Join Date: Aug 2014
Location: Midlands
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
Hi all, been away for a while, pretty much lost interest in car forums as a whole so took a break away from it. I did manage to get some stuff done on the car though.
Next up is a trip upto Revolution for the wheels and tyres, Eibach lowering springs and geometry set up then the next day to AET Motorsport for Hyperflow Induction kit, full Milltek, RCM sump baffle kit and a remap.
Next up is a trip upto Revolution for the wheels and tyres, Eibach lowering springs and geometry set up then the next day to AET Motorsport for Hyperflow Induction kit, full Milltek, RCM sump baffle kit and a remap.
What wheels you going for?
Last edited by FrozenFlame; 09 March 2015 at 09:53 PM.
Scooby Regular
Its not as easy to change it as older models, plus I am running 405bhp with this stock one so not much point as its not restricting.
Scooby Regular
Scooby Regular
iTrader: (9)
Join Date: Nov 2010
Location: Cheltenham
Posts: 1,067
Likes: 0
Received 0 Likes
on
0 Posts
Yes found the problem now. Its where i have changed the turbo intake pipe as need a 3inch intake. The oem intake pipe is slightly longer than my 3 inch one.
So need to make a coupler sort of thing to gain abit more length. Will get a photo up ones all sorted!
Thanks again
Scooby Regular
Nice, can you let us know which Eibach lowering springs you get and how much of a drop they give. I've seen contradicting info regarding the drop as they seem to get listed showing the amount of drop on a wrx. The sti is lower as standard and supposedly doesn't drop as much overall. I would like to lower mine too, preferably about 20mm front and rear so any info would be appreciated.
What wheels you going for?
What wheels you going for?
I'm going for 18" Rota Grid Drifts in Matt Bronze.
Nice! Put some pics up when you have got them. I'm thinking of changing my wheels but not too sure what to go for. I've got 2 sets of GT1's, gunmetal in summer and gold for my winter tyres. Quite fancy bronze...
Could do with filling the arches out a bit more too. What width tyre and offset can these hatches run without issue?
Could do with filling the arches out a bit more too. What width tyre and offset can these hatches run without issue?
Scooby Regular
Scooby Regular
1) Matt-c
2) ryanj1993
3) Harry Kovert
4) JamieJerkovic
5) domino46
2) ryanj1993
3) Harry Kovert
4) JamieJerkovic
5) domino46
Scooby Regular
Hi, does anyone know where I can get a transmition rebuild kit for the sti 6 speed my gearbox has got quite noisey in 1st and 2nd specialy very winey on downshifts into 2nd but looking at new boxes they seam to be very expencive and I'm pritty sure a rebuild kit is available just don't know where from .. Thanks Alex
Last edited by kershaw-330s; 10 March 2015 at 04:24 PM.
Scooby Regular
iTrader: (5)
Rad Top Hose
Following installation of shiny new alloy rad I have a bit of an issue with the top hose fouling the plastic part of the fan cowling.
Question is, could I remove hose from radiator, trim it and refit it without having to drop the coolant?
Question is, could I remove hose from radiator, trim it and refit it without having to drop the coolant?
Scooby Regular
iTrader: (5)
Hi, does anyone know where I can get a transmition rebuild kit for the sti 6 speed my gearbox has got quite noisey in 1st and 2nd specialy very winey on downshifts into 2nd but looking at new boxes they seam to be very expencive and I'm pritty sure a rebuild kit is available just don't know where from .. Thanks Alex
Scooby Regular
iTrader: (5)
1) Matt-c
2) ryanj1993
3) Harry Kovert
4) JamieJerkovic
5) domino46
6) kershaw-330s
7) wrx-sok
8) Benji554
9) duanned123
10)
2) ryanj1993
3) Harry Kovert
4) JamieJerkovic
5) domino46
6) kershaw-330s
7) wrx-sok
8) Benji554
9) duanned123
10)
Last edited by matt-c; 10 March 2015 at 06:28 PM.