wagon fettle
#1171
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
Cheers Jura...dip is gonna kick *** and make a nice centre piece to the car. My choice matches the black ad grey theme perfectly, but its gonna be marmite
#1173
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
soonish...well maybe...probably
Diff has arrived at TEG Sport, should be done next week; interior has arrived with Phil at Flock It, should be done by Friday AND I have two possible DCCD looms. I'm not holding my breath but it all sounds good
Diff has arrived at TEG Sport, should be done next week; interior has arrived with Phil at Flock It, should be done by Friday AND I have two possible DCCD looms. I'm not holding my breath but it all sounds good
#1179
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
a fan club dedicated to taking the pi55 out of my glacial like progress
all black Jura, i decided with the Wicked coatings stuff best to keep it simple and make that the attention grabber
all black Jura, i decided with the Wicked coatings stuff best to keep it simple and make that the attention grabber
#1182
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
Getting there old man...you know how it is
Ironically Gus two turned up in a week and one was only 90minutes from my house! I've already got a buyer for Deans' loom and let him know so sorted all round...thanks again for your help
And here it is...
Stripped, quite a bit of waste!
All I needed...i'm going to remove the connector blocks and solder\shrink wrap the wires. All I need to do then is work out where to splice some cables in.
My interior parts have been finished at Wicked Coatings...stoked they look awesome. They are already on thier FB page but I will post some photos once they arrive and the abuse can start
Ironically Gus two turned up in a week and one was only 90minutes from my house! I've already got a buyer for Deans' loom and let him know so sorted all round...thanks again for your help
And here it is...
Stripped, quite a bit of waste!
All I needed...i'm going to remove the connector blocks and solder\shrink wrap the wires. All I need to do then is work out where to splice some cables in.
My interior parts have been finished at Wicked Coatings...stoked they look awesome. They are already on thier FB page but I will post some photos once they arrive and the abuse can start
Last edited by trails; 20 May 2012 at 07:36 PM.
#1188
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
loom all nicely wrapped, thanks to Scott for the tension It all fits too, which is nice. I've cut out the connectors out and just need to join the wires...a job for tomorrow night.
#1199
Scooby Regular
Thread Starter
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
Trev if I had nothing else to do I'd have finished it by now...honest
Thanks Floyd, I'd say until you take this kind of build on it's far too easy to underestimate how many disparate threads there are to pull together to make it work!!
Thanks Floyd, I'd say until you take this kind of build on it's far too easy to underestimate how many disparate threads there are to pull together to make it work!!