any one have any about they wanna sell or no where can buy cheap cheers rob

 

I have a uppipe to header gasket. I don't have the upipe to turbo one tho.
Its not a genuine subaru one but you can have it for a fiver delivered.

 

Oh sweet send pay pal il send funds tomorrow . Right just other gasket anyone got one. Also a decent downpipe gasket

 

don nedly looks like a center section 1 lol i need 3 bolt up pipe gaskets

 

it is the gasket for between the upipe/headers as i said.
Like i said i dont have the top one that goes between uppipe/turbo (3bolt)

 

Hi. I bought the gaskets from Harvey Smiths on here. Send him a PM or give him a call tomorrow.
Landline: (0)1325 283294
Mobile: 07860 302020

Hope this help.

 

Harvey is defo the best person to talk about exhausts, gaskets etc.

 

lol Rob you have exactly the same problem i have! haha except mine is the gasket between the headers and up-pipe. I replaced it and blew it again the next week!

Which gaskets you need mate i have 2 sets of the full 3" kit but missing some.

 

I need bottom uppipe top of up pipe and down pipe ones mate

 

The one i offered you is the bottom uppipe gasket.
From this set:
http://www.ebay.co.uk/itm/2208745728...84.m1439.l2649

A better full set is pretty easy to find:
try here:
http://shop.grahamgoode.com/individu...ts-24481-c.asp

 

i dont have a clue what gaskets i need lol im fitting gt spec s and a harvey up pipe and got 2 new manifolds one thats it . so what else do i need?

 

if you are getting them from harvey just ask him to supply all the gaskets you need.

 

If it blew within a week there is something far wrong and I suggest you slacken off the 3 bolts holding the headers to head on each side, the uppipe to collector bolts and if they are OE cast headers slacken slightly the two connections to the crosspipe then starting with each cylinder head, torque up each fastener evenly one side at a time. Then tighten evenly the header to uppipe connection and the two crosspipe connections bit by bit. Finally tighten the uppipe to turbo connection, three nuts plus the two bracket nuts. You will now have tightened the whole assembly in such a manner that it sits properly.
If your uppipe is sold you are likely to go through quite a few collectors to uppipe gaskets and it is for this reason that all my uppipes are slip jointed to relieve thermal stress during heat cycling. This also greatly reduces the possibility of the headers cracking.
If you are running GT Spec tubular headers you should be running my trick 3 bolt uppipe anyway because of the proven improved spool and torque right across the rev range.

Gaskets : The gaskets on GT2 header sets are as follows :
2 x Head to Exhaust Manifold/header. These rarely require replacement.
1 x 3 bolt Collector to Uppipe. These can go regularly if fitting work was not done properly or a solid uppipe is in use.
1 x Uppipe to Turbo. These rarely require replacement.
Although some people frown on the practice we will not replace gaskets needlessly when there is nothing wrong with the original, the exception being the 3 bolt header to uppipe gasket, particularly when solid uppipes are in use.
If using OE Subaru 4 piece header and uppipe set :
Exactly as above 2 x head to exhaust. Rarely replaced.
2 x 2 bolt gaskets at either side of the crosspipe.
1 x Larger 2 bolt gasket collector to uppipe. The OE uppipe has an expansion banjo but this is the most likely gasket to go on an OE header set and very likely to go at some point when the OE uppipe has been replaced with a solid uppipe.
1 x uppipe to turbo gasket. This is triangularish in shape, 3 bolt, very rarely replaced.
ITH.

 

Ok sweet don so u have the bottom up pipe gasket ? But that only has 2 holes and I need a top gasket? Can some1 show me link for right gaskets on bay cheers Harvey il be ordering uppipe for a sc40 this week.

 

yes mate the bottom of the upipe has 2 bolts and the top has 3 or 5.
The gasket i have will fit the bottom of the uppipe. Sorry, I don't know how else to explain it to you. Harvey's response was very comprehensive.

Here are some links to help:
top uppipe gasket: http://shop.grahamgoode.com/impreza-...44-66525-p.asp
bottom uppipe gasket: http://shop.grahamgoode.com/impreza-...45-66526-p.asp

 

how much again for bottom 1 don?


any top up pipe gaskets and downpipe ones?

 

fiver posted

 

Sweet il pay pall tomorrow evening