Standard Re-Circ Dumpvalve
#1
Standard Re-Circ Dumpvalve
Hello
I am after a standard Dump valve which will fit my MY93 WRX Turbo
I have been having problems getting a dump valve to work properly with my FMIC
HKS gave me fud dud dud dud sounds when coming of med throttle
Forge Re-circ is causing car to stall when coming off throttle and rev's falling. Tried diffo springs, got idle ok, but got the Fud dud dud dud noise again
Tried Forge Atmos twin valve, played with springs, either go to strong and get fud dud dud dud dud noise again, or correct noise, but when on motorway and coming of throttle slightly, valve stays open hissing...
So been advised to 'try' a standard re-circ one... Anyone got one????
Also is it 1 inch bore inlet and outlet?
Cheers
Rob White
(rj.white@blueyonder.co.uk)
I am after a standard Dump valve which will fit my MY93 WRX Turbo
I have been having problems getting a dump valve to work properly with my FMIC
HKS gave me fud dud dud dud sounds when coming of med throttle
Forge Re-circ is causing car to stall when coming off throttle and rev's falling. Tried diffo springs, got idle ok, but got the Fud dud dud dud noise again
Tried Forge Atmos twin valve, played with springs, either go to strong and get fud dud dud dud dud noise again, or correct noise, but when on motorway and coming of throttle slightly, valve stays open hissing...
So been advised to 'try' a standard re-circ one... Anyone got one????
Also is it 1 inch bore inlet and outlet?
Cheers
Rob White
(rj.white@blueyonder.co.uk)
#2
Former Sponsor
iTrader: (48)
Rob: If it helps you the O/E D.V from a '95 WRX is 20mm dia in and out, fairly soft spring and the pressure pushes against the side of the piston and not the piston face itself as with a Forge. I have had similar problems myself this week setting up my WRX after injectors, Hybrid FMIC, TD05-06 from Andy F and so on. Having fitted a red spring to the Forge recic after giving up on a VTA, I had it shimmed to 8mm and was not solving the problem although it was moved up the boost range. Andy had mentioned to me that I should try a softer D.V. so a Seat Ibiza item courtesy of Jonny Gav was fired on. Pretty soft spring.........................Problem solved.
Hope this helps you.
BTW. I will do experiments with the O/E this week-end, then it will be for sale £30 plus £3 postage.
What turbo and intercooler are you running?
Hope this helps you.
BTW. I will do experiments with the O/E this week-end, then it will be for sale £30 plus £3 postage.
What turbo and intercooler are you running?
#3
Running a VF34 Turbo at 1.1 bar with HKS FMIC
Will be fitting a Fuel Pressure reg soon and run it at 1.3 bar
Let me know how you get on with the O/E DV
First dibs on you e O/E one please sir!!
Cheers
Rob
Will be fitting a Fuel Pressure reg soon and run it at 1.3 bar
Let me know how you get on with the O/E DV
First dibs on you e O/E one please sir!!
Cheers
Rob
#5
Hello Harvey
How did you get on, is the standard Dump Valve still for grabs
Cheers
Rob
rj.white@NOSPAMblueyonder.co.uk
Please remove the 'NOSPAM' bit !
How did you get on, is the standard Dump Valve still for grabs
Cheers
Rob
rj.white@NOSPAMblueyonder.co.uk
Please remove the 'NOSPAM' bit !
Thread
Thread Starter
Forum
Replies
Last Post
shorty87
Wheels And Tyres For Sale
0
29 September 2015 02:18 PM