Simtek Issue's
#1
Scooby Regular
Thread Starter
iTrader: (4)
Join Date: May 2002
Location: Swansea
Posts: 2,072
Likes: 0
Received 0 Likes
on
0 Posts
Simtek Issue's
Right, not sure if anyone can help but since i've had my simtek fitted the car overheats quite quickly once i give it a bit of stick and the Defi's oil temp gauge goes over 105degree's pretty quick
Any idea's what can cause this ?
Also, i tried to use the launch control the other night and previously i had to take the car to 4600rpm - now when it's switched on the car wont rev past 4000rpm to launch
Any idea's what can cause this ?
Also, i tried to use the launch control the other night and previously i had to take the car to 4600rpm - now when it's switched on the car wont rev past 4000rpm to launch
#3
Scooby Regular
Thread Starter
iTrader: (4)
Join Date: May 2002
Location: Swansea
Posts: 2,072
Likes: 0
Received 0 Likes
on
0 Posts
The Simtek was fitted by APi
The only reason i thought they might be related is because it never done it before the Sim was fitted
Also, should i have had my old ECU back ?
The only reason i thought they might be related is because it never done it before the Sim was fitted
Also, should i have had my old ECU back ?
#7
Former Sponsor
iTrader: (4)
Join Date: Jul 2003
Location: @Junc 12, M40 Warwicksh; 01926 614522 CV33 9PL -Use 9GX for Satnav. South Mids Alcatek ECu dealer
Posts: 6,377
Likes: 0
Received 3 Likes
on
3 Posts
We normally leave the old ecu board inside the car in the wrapping that comes from Simtek. If not, then we can send it on to you. It has no value to us. I seem to recall that we were on a late job with your car and it probably got left in the rush to get you away.
The overheating of the engine and oil are, quite correctly, not related to the remapping. It is possible that something has gone adrift in the engine in the recent hot spell.
The programme for the launch control should not vary. Once programmed it should be set in stone. l guess that something else may be going on.
Seek help from a specialist about the temperature problems as soon as possible in case you are harming the engine.
David APi
The overheating of the engine and oil are, quite correctly, not related to the remapping. It is possible that something has gone adrift in the engine in the recent hot spell.
The programme for the launch control should not vary. Once programmed it should be set in stone. l guess that something else may be going on.
Seek help from a specialist about the temperature problems as soon as possible in case you are harming the engine.
David APi
Trending Topics
#8
Scooby Regular
Thread Starter
iTrader: (4)
Join Date: May 2002
Location: Swansea
Posts: 2,072
Likes: 0
Received 0 Likes
on
0 Posts
Thanks David - yeah it was a bit of a late one
The Launch control has worked fine but for some reason the other day it just wouldnt let me rev up to the 4600rpm required, soon as i turn it off it was fine
The car is booked in the garage for Wednesday for all coolants to be checked and to check the rad to make sure its ok
The Launch control has worked fine but for some reason the other day it just wouldnt let me rev up to the 4600rpm required, soon as i turn it off it was fine
The car is booked in the garage for Wednesday for all coolants to be checked and to check the rad to make sure its ok
Last edited by scoobyp1; 05 July 2010 at 01:43 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Phil3822
General Technical
0
30 September 2015 06:29 PM