17 inch wheels
just had 17 inch wheels fitted on standard suspension , am going to have it 4 wheel aligned is there any special measurments i need to know to tell the bloke doing the job, cheers .
Scooby Regular
Joined: Nov 2001
Posts: 8,238
Likes: 0
From: the middle bit
er my advice would be to go somewhere decent where they dont need to be told. I did do a geometry thing somewhere more local & slightly cheaper but wasn't as pin point accurate as the set up i got from TSL (who i am in no way linked with
)
Si
)Si
Scooby Regular
Joined: Nov 2001
Posts: 8,238
Likes: 0
From: the middle bit
as in even the prodrive setting they used at first place while they were within guidelines these are pretty damn wide so was nice to go with the NOttingham based boys who had an even more tweaked & less flexible set up, bonus
Good plan doing it straight away mind i managed to baldify my first tyres when i went 17"
Si
Good plan doing it straight away mind i managed to baldify my first tyres when i went 17"
Si
Scooby Regular
Joined: Nov 2001
Posts: 8,238
Likes: 0
From: the middle bit
well it was just one of the front ones was bald on the inside edge from where it hadnt/wasnt set up properly, took about 4 months circa 2000 miles (before i noticed it 
) so woodnt worry yet but full geometry definately cunning
Si
PS where r u based/going to cant hurt to ask some local scooby owners where they go at a guess
) so woodnt worry yet but full geometry definately cunning Si
PS where r u based/going to cant hurt to ask some local scooby owners where they go at a guess
Scooby Regular
Joined: Dec 2001
Posts: 6,963
Likes: 0
From: Just far enough from sunny Liverpool
geometry is always going to be a compromise.
max grip = shagged tyres pdq etc.
my track setting sre as follows;
as much neg camber as poss both front and rear, just make sure both sides are set the same. should maybe get 1m25 (ish).
front total toe in .8 (ie .4 each side), rear toe in .4 (ie .2 each side).
the above settings give a very neutral feel on track. just don't get the castor angles the wrong way round unless you like going backwards
hope this helps,
simon
[Edited by RRH - 6/25/2003 8:27:48 AM]
max grip = shagged tyres pdq etc.
my track setting sre as follows;
as much neg camber as poss both front and rear, just make sure both sides are set the same. should maybe get 1m25 (ish).
front total toe in .8 (ie .4 each side), rear toe in .4 (ie .2 each side).
the above settings give a very neutral feel on track. just don't get the castor angles the wrong way round unless you like going backwards
hope this helps,
simon
[Edited by RRH - 6/25/2003 8:27:48 AM]
Trending Topics
Scooby Regular
Joined: Oct 2001
Posts: 1,833
Likes: 0
Why toe-out should be bad?
I belive max camber rear/front with some toe out rear(say 1-2mm total)/zero toe front eliminates understeer right?
Toe out is an unstable situation but gives lively feeling whereas toe in is more stable but doesn't help the steering. It depends from what you want from your car, personally I'd like a neutral to oversteering car.
JIM
I belive max camber rear/front with some toe out rear(say 1-2mm total)/zero toe front eliminates understeer right?
Toe out is an unstable situation but gives lively feeling whereas toe in is more stable but doesn't help the steering. It depends from what you want from your car, personally I'd like a neutral to oversteering car.
JIM
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
34
Nov 7, 2024 04:10 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
20
Oct 22, 2015 06:12 AM
