Arch

iTrader: (59)

Having a mini clear out of a few bits that are no longer needed.

I have a brand new TR 5 Speed gearbox mount which I bought as part of the kit from Scoobyclinic last month. I only needed the engine mounts so this is available. This really is about as good as it gets without solid mounting the gearbox and is considerably stiffer than the Hardrace or GpN mounts. SOLD

Shown as the kit at the bottom of the page below.

http://www.scoobyclinic.com/products...ts_gaskets.htm





Classic chrome metal oil filler pipe. I bought this but forgot I had it and now have AVCS heads which use a different filler pipe. I have never seen on of these before and it really is well made and looks really good. Looking for £45



Set of classic alloy arms complete with pins ready to fit straight on. These have been powder coated silver, there are a couple of chips but nothing major and really do look good. Looking for £80





Set of newage alloy arms removed from a blobeye. In good condition but have no rear mounting pins. The pins are the same classic and newage. SOLD


Newage brake master cylinder and servo removed from a low mileage blob STI. Looking for £40



Lightweight alloy ECU cage. I used this to get rid of the heavy standard ECU mount and foot rest. I had it mounted on the passengers side transmission tunnel and had a Power FC fitted but will fit all classic standard ECU's and I assume newage. It has holes at the back to allow the plugs to be fitted and holes in the side to allow the com port to be accessed.








Early Classic heater controls. Looking for £10



Set of Ver3/4 metal cam pulleys remove from the engine earlier this year.
Heads sold so these no longer needed. SOLD





Newage STI intercooler hose from underside Y-Pipe. £10



Set of newage front hubs £80

2 Pin alternator £20

5 speed starter x2 £15 each

All the above prices are plus postage at cost. Happy to take payment by paypal but buyer needs to pay the fees or send payment a s a gift.

leecalcars

iTrader: (37)

Hi Arch how much for the ecu case assuming my simtek would fit ?

cheers lee

Arch

iTrader: (59)

Lee
Sorry forgot to put a price on it, £27 delivered. If your simtek is in a standard case it will fit.

RAPID RABBIT

iTrader: (10)

Will the metal pulleys fit a version 2 and version 6?

Arch

iTrader: (59)

They will fit Ver 1-4 but not Ver 6.

Arch

iTrader: (59)

PM's replied to

Arch

iTrader: (59)

Also have this set up which I bought from Pedro on 22B. I never got round to fitting it as it is designed to fit with the newage master cylinder above. It allows an adjustable brake bias valve, included, to be used with the standard set up. I cannot remember how it plumbs in but I am sure i could find out. The kit includes all the braided hoses and fittings required and the compbrake adjustable bias valve. Looking for £110



Picture fitted doesnt show it to well unfortunately.

RAPID RABBIT

iTrader: (10)

Pmd about pullys

Arch

iTrader: (59)

Replied.

Arch

iTrader: (59)

Pulley's sold

Arch

iTrader: (59)

btt

shag

iTrader: (10)

hi mate how much for the newage bottom arms posted?

Arch

iTrader: (59)

£8 should cover the postage so £48 delivered.

Arch

iTrader: (59)

open to sensible offers on these bits

Arch

iTrader: (59)

BTTT

Barracuda_82

iTrader: (3)

Have you got my message about the ECU case?

Arch

iTrader: (59)

PM sent

Arch

iTrader: (59)

BTTT

Arch

iTrader: (59)

No takers?

Arch

iTrader: (59)

Gearbox mount sold

Arch

iTrader: (59)

open to offers on the bits left

Arch

iTrader: (59)

bttt

Arch

iTrader: (59)

BTTT

Arch

iTrader: (59)

Newage arms sold

Arch

iTrader: (59)

BTTT