MDX321T, 625cc injectors, Harvey Up-pipe, stainless headers
27 March 2017, 09:50 PM
#1
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
MDX321T, 625cc injectors, Harvey Up-pipe, stainless headers
Evening. Got a few bits from my car up for sale, going down a different route so all bits are off and ready to go now.
All items can be collected from Leigh Lancashire or I can post for cost but I'm sorry I'm not doing the whole dibs thing. First to pay or secure with a deposit secures the item.
Payment on collection or via PayPal as a gift or if not then please cover fees.
First up is my MDX321T, just over 2 years old in full working order, slight play in shaft as expected with this turbo.
Unsure of mileage as I bought it second hand.
Was running 380bhp on my car which I thought was low but found out tonight I have no compression on 1 cylinder so was doing well I think at 1.6 bar.
Has some slight marks on the tips of the compressor wheel but ran perfectly for me no problem. Has a snapped stud which I will replace prior to sale.
I'm after £1000 for this.
All items can be collected from Leigh Lancashire or I can post for cost but I'm sorry I'm not doing the whole dibs thing. First to pay or secure with a deposit secures the item.
Payment on collection or via PayPal as a gift or if not then please cover fees.
First up is my MDX321T, just over 2 years old in full working order, slight play in shaft as expected with this turbo.
Unsure of mileage as I bought it second hand.
Was running 380bhp on my car which I thought was low but found out tonight I have no compression on 1 cylinder so was doing well I think at 1.6 bar.
Has some slight marks on the tips of the compressor wheel but ran perfectly for me no problem. Has a snapped stud which I will replace prior to sale.
I'm after £1000 for this.
Last edited by ianbott; 27 March 2017 at 09:56 PM.
27 March 2017, 09:55 PM
#3
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
Next up is my Harvey smith up-pipe bought from AS performance, basically as new. Will come with a full set of studs on the top, currently one missing.
I'm looking for £80 for this.
I'm looking for £80 for this.
27 March 2017, 10:01 PM
#4
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
Stainless headers up next, these are from Williams motorsport and flowed really well on my motor.
They are heat wrapped and in really good condition.
They are standard two bolt up-pipe fitting and fit really well.
They have an additional boss welded in to relocate the oxygen sensor which is NOT included but come with a bung to plug the hole.
I'm looking for £175 for these.
They are heat wrapped and in really good condition.
They are standard two bolt up-pipe fitting and fit really well.
They have an additional boss welded in to relocate the oxygen sensor which is NOT included but come with a bung to plug the hole.
I'm looking for £175 for these.
Last edited by ianbott; 27 March 2017 at 10:07 PM.
27 March 2017, 10:16 PM
#7
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
625cc topfeed injectors up next, sorry will get photos of these through the week, completely forgot while I was at my lockup.
these ran 490bhp along with the MDX321T on the car I bought them both from.
Fit in standard fuel rails.
I'm looking for £200
Got a zerosports low temp stat too, good working order £20
RCM come filter including aluminium trumpet, the trumpet has a hole used for a maf which I have taped up with no I'll effects. In good working order but has some damage as seen.
Looking for £60
Also got this turbo inlet pipe I made, works really well and almost impossible to collapse like some silicone pipes.
£60 for this please
these ran 490bhp along with the MDX321T on the car I bought them both from.
Fit in standard fuel rails.
I'm looking for £200
Got a zerosports low temp stat too, good working order £20
RCM come filter including aluminium trumpet, the trumpet has a hole used for a maf which I have taped up with no I'll effects. In good working order but has some damage as seen.
Looking for £60
Also got this turbo inlet pipe I made, works really well and almost impossible to collapse like some silicone pipes.
£60 for this please
Trending Topics
27 March 2017, 10:19 PM
#9
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
27 March 2017, 10:41 PM
#14
Scooby Regular
iTrader: (1)
Join Date: Jan 2017
Location: Chichester
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Ok mate, I'm just gonna double check, been looking for a set of these for my build as bought a built bottom end from graham hickman at group b and these Williams headers were advised, can you give me till midday tomorrow at the latest please to make sure they will be ok for my engine
27 March 2017, 10:49 PM
#15
Scooby Regular
iTrader: (1)
Join Date: Jan 2017
Location: Chichester
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Just had a quick check, looks the same right through 2001-2007 so I will definitely have these, any chance we can do a deal on the headers and the up pipe together posted
27 March 2017, 10:59 PM
#16
Scooby Regular
Thread Starter
Join Date: May 2008
Location: Warrington
Posts: 632
Likes: 0
Received 0 Likes
on
0 Posts
03 April 2017, 11:14 PM
#20
hello mate can you send me pics of the damage to the fins and how much play is actually in the shaft? send to g4va@hotmail.com or 07976126501
