Bugeye reflector covers
#1
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: JDM WRX STi7 Scooby
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Bugeye reflector covers
I have brought some reaplcement covers from Scooby parts - the carbon fibre ones with STi on them. I was expecting replacement clip in reflectors but what's actually turned up appears to be stick on carbon effect covers. Is this right ?? Is this what other people have ??
#3
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: JDM WRX STi7 Scooby
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by redxiii
Thats right Mav, there should be some double sided tape to stick them over the relfector.
Where did you get yours from if you dont mind me asking ?
Where did you get yours from if you dont mind me asking ?
#4
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: JDM WRX STi7 Scooby
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Right bit of an odd one here me thinks
Went to fit the stick-on's only to find that the drivers side reflector is not totally flat it has a raised ridge in the middle and thus the stick on cover dosen't go on properly. The passenger side reflector is "normal" - I.E flat so that one would be fine.
Do the standard reflectors come off in any way ?? are these stick on bits themselves or are they clipped into the bodywork somehow ?? The only way I can see round this at the moment (short of trying to replace the reflector in someway) is to very carefully smash the reflector ridge to flatten it and then stick the cover on over the top which will seal the hole anyway.
Any other suggestions ??
Went to fit the stick-on's only to find that the drivers side reflector is not totally flat it has a raised ridge in the middle and thus the stick on cover dosen't go on properly. The passenger side reflector is "normal" - I.E flat so that one would be fine.
Do the standard reflectors come off in any way ?? are these stick on bits themselves or are they clipped into the bodywork somehow ?? The only way I can see round this at the moment (short of trying to replace the reflector in someway) is to very carefully smash the reflector ridge to flatten it and then stick the cover on over the top which will seal the hole anyway.
Any other suggestions ??
#5
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: JDM WRX STi7 Scooby
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Ok folks you can ignor the above post. Decided to try a little brute force to see what was behind the reflector and it's not alot. By the looks of things it's supposed to come out before you stick the carbon reflector on.
#6
Scooby Regular
Join Date: Feb 2006
Location: Chelmsford
Posts: 591
Likes: 0
Received 0 Likes
on
0 Posts
yeah i think thats right, ive just ordered the same ones as you and thats what i was gonna do lol... but my reflectors didnt have the funny raised bit you mention
#7
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: JDM WRX STi7 Scooby
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TimmyboyWRX
yeah i think thats right, ive just ordered the same ones as you and thats what i was gonna do lol... but my reflectors didnt have the funny raised bit you mention
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM