Notices
ScoobyNet General General Subaru Discussion

Had enough of subarus.

Thread Tools
 
Search this Thread
 
Old 29 March 2013, 01:26 PM
  #1  
Drewrayner1
Scooby Newbie
Thread Starter
 
Drewrayner1's Avatar
 
Join Date: May 2012
Location: Maesteg
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default Had enough of subarus.

After spending £500 on a timing belt, water pump, oil pump change etc last a week last Tuesday the piece of s###e is still not running properly. Tried bleeding the Cooling system everyday for a week and a half using every method mentioned on here and still no joy. Car is running fine, no smoke from exhaust, no water in oil or vice versa, had a block test done which it passed car idles and runs without misfire but drinks coolant like I drink jack Daniels and absolutely stinks of coolant when warmed up. Can't find any leaks anywhere. Bubbling sound coming from behind dash when first started and everytime I accelerate. Try to bleed system, but within about a minute of starting the engine from cold with header tank cap of it the coolant keeps rising and overflowing. Had enough now. Think its time to get rid.

Last edited by Drewrayner1; 29 March 2013 at 01:27 PM.
Old 29 March 2013, 01:27 PM
  #2  
tubbytommy
BANNED
iTrader: (20)
 
tubbytommy's Avatar
 
Join Date: Mar 2010
Location: crawley :)
Posts: 16,950
Likes: 0
Received 1 Like on 1 Post
Default

See yah then.
Old 29 March 2013, 01:40 PM
  #3  
stonejedi
Scooby Regular
iTrader: (51)
 
stonejedi's Avatar
 
Join Date: Jan 2008
Posts: 7,439
Received 149 Likes on 109 Posts
Default

My advice would be to take the car to a Subaru specialist and let them have a check around your car to diagnose the exact problem,they are great cars but need servicing and repairing by engineers that know exactly what they are doing,if you get my drift.SJ.
Old 29 March 2013, 01:59 PM
  #4  
stevebt
Scooby Regular
iTrader: (8)
 
stevebt's Avatar
 
Join Date: Sep 2002
Posts: 16,732
Received 33 Likes on 19 Posts
Default

13 posts, I don't know how Scoobynet will survive without your input
Old 29 March 2013, 02:05 PM
  #5  
m_reed
Scooby Regular
iTrader: (1)
 
m_reed's Avatar
 
Join Date: Sep 2007
Posts: 135
Likes: 0
Received 0 Likes on 0 Posts
Default

he is only blowing off abit of steam as he is pissed off no need for sarky comments mind.

Try and keep your chin up bud and carry on sure yu will get there in the end mate, heater matrix not leaking is it?
Old 29 March 2013, 02:05 PM
  #6  
drew25
Scooby Regular
 
drew25's Avatar
 
Join Date: Jun 2011
Location: Northern Ireland
Posts: 91
Likes: 0
Received 0 Likes on 0 Posts
Default

Makes me laugh
Old 29 March 2013, 02:25 PM
  #7  
craigybaby
Scooby Regular
iTrader: (8)
 
craigybaby's Avatar
 
Join Date: Feb 2011
Location: redditch
Posts: 1,899
Likes: 0
Received 0 Likes on 0 Posts
Default

I wouldn't get rid mate just take it to a specialist near you it's probably summot really silly what area you from
Old 29 March 2013, 02:31 PM
  #8  
yabbadoo4
Scooby Regular
iTrader: (8)
 
yabbadoo4's Avatar
 
Join Date: Mar 2011
Location: planet subaru
Posts: 3,245
Received 15 Likes on 13 Posts
Default

chin up bud, phone the nearest specialist to you and see if they can help diagnose the problem. they are not a sympathetic bunch round here. good luck with it.
Old 29 March 2013, 02:43 PM
  #9  
Osimabu
Scooby Regular
iTrader: (2)
 
Osimabu's Avatar
 
Join Date: May 2011
Location: .
Posts: 1,341
Likes: 0
Received 0 Likes on 0 Posts
Default

It will be something daft, but, as a plumber, I know just how frustrating water can be on occasions, so you have my sympathy.

It's worth double checking that everything is re-connected to the right place and to ensure there wasn't something blanked off during the water pump swap that has accidentally been left blocked.

If the pump is trying to circulate the water and can't, it will have to go somewhere, and that's possibly why it's coming back out of the filler cap.

It could be an air lock, but equally it could be a physical obstruction. Have you left the heater set to hot when trying to re-fill it?

Just remember what a good car it is when it's running well, and allow it its little foibles, and you'll soon get it sorted.
Old 29 March 2013, 03:24 PM
  #10  
Firez34
Scooby Regular
iTrader: (5)
 
Firez34's Avatar
 
Join Date: Jun 2011
Location: Chesterfield
Posts: 566
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Drewrayner1
After spending £500 on a timing belt, water pump, oil pump change etc last a week last Tuesday the piece of s###e is still not running properly. Tried bleeding the Cooling system everyday for a week and a half using every method mentioned on here and still no joy. Car is running fine, no smoke from exhaust, no water in oil or vice versa, had a block test done which it passed car idles and runs without misfire but drinks coolant like I drink jack Daniels and absolutely stinks of coolant when warmed up. Can't find any leaks anywhere. Bubbling sound coming from behind dash when first started and everytime I accelerate. Try to bleed system, but within about a minute of starting the engine from cold with header tank cap of it the coolant keeps rising and overflowing. Had enough now. Think its time to get rid.
Hi fella, when you bleed it the coolant will overflow out the tank and keep overflowing until the thermostat opens and the fans kick in. Just let it overflow until the stat opens and leave until the stat open and the fans kick in 3 times then top the coolant up and put the cap back on. Make sure the heaters set to hot as well. It takes a while for the temp to get hot enough for the stat to open from cold when the cars idling so it will spill quite a bit. You may have a bad tank cap that not holding pressure and also when I was losing coolant it was the plastic on the side of the rad which had cracked now it didn't leak at all when upto temp but when the car was put on boost the pressure was enough to open the crack and let it release coolant. Check hoses and check your carpet inside just incase the heater matrix is leaking inside the car. Hope this helps a bit I now how frustrating car niggles can be like most of us that own them.
Old 29 March 2013, 03:24 PM
  #11  
weirdfish
Scooby Regular
 
weirdfish's Avatar
 
Join Date: Jan 2013
Location: Glos
Posts: 305
Likes: 0
Received 0 Likes on 0 Posts
Default

Who done all the work mentioned? I would go with the above comments, check everything is back as it should be, all pipe connected correctly etc etc.
Is the water purely coming back out the filler cap or is it coming from somewhere else, if the water is circulating correctly then the air should eventually find it's way out if you leave the cap off long enough.
There are some helpful people on here, after all it is a car forum, and if you can't vent your spleen from time to time without getting shot down in flames then some members need to get from behind their keyboards a bit more.
Old 29 March 2013, 03:30 PM
  #12  
sprigeteer
Scooby Regular
iTrader: (9)
 
sprigeteer's Avatar
 
Join Date: Aug 2008
Posts: 868
Likes: 0
Received 1 Like on 1 Post
Default

Keep at it mate. They reward patience and once you have sorted it you will have a very reliable motor. Weve all been there with cars at one point or another.
Old 29 March 2013, 03:35 PM
  #13  
edger-360
Scooby Regular
 
edger-360's Avatar
 
Join Date: May 2007
Location: west mids
Posts: 57
Likes: 0
Received 0 Likes on 0 Posts
Default

mate had a similar experience,small hole in rad could not find it as coolant went onto the engine and evaporated
took it to a local specialist one new rad job done happy days
Old 29 March 2013, 03:36 PM
  #14  
ALi-B
Moderator
Support Scoobynet!
iTrader: (1)
 
ALi-B's Avatar
 
Join Date: Apr 2002
Location: The hell where youth and laughter go
Posts: 38,034
Received 301 Likes on 240 Posts
Default

If the car is using coolant, there has to be a leak...be it internal or external.

There are two methods to test this, a good garage will have the equipment to do both.

First is a pressure tester. Its just a pump and guage that fits to the header tank, it will show any pressure loss on the guage and at the same time will force water out of any external leaks. Small leaks may take a while...the car needs to be bone dry, the undertray needs to come off and park the car over some cardboard (obviously that doesn't check the heater matrix). Common leaks are from the plastic ends on the radiator...tiny hairline cracks form around the elbow fittings, which only leak when the system is under pressure.

Second test is testing for combustion gases in the coolant. This can be done througha number of methods - electronic gas analyser, test paper or a bottle and some test dye.

Combustion gasses in the coolant can be from a head gasket, cracked cylinder liner or cracked/warped cylinder head (the latter is rare). A failed head gasket does not usually usually cause oil+water mixing. Oil+water is only one way a gasket can fail and they can fail in many different ways. More common gasket failures actually show up as combustion gases leaking into the coolant and the system overpressurising (venting coolant out the overflow) when the car is driven hard.

Of course you could just have a faulty header tank cap. Not a regular problem, but not unheard of either.


Airlock would not cuase coolant loss....although it may appear like that, as the air is purged from the system the coolant level will fall. Or in the worst case the airlock has caused a head gasket to fail from localised overheating, (the temperature guage won't always show that the engine is overheating ), so now the coolant loss is from the head gasket, but originally caused by an airlock.

Hope that helps

Last edited by ALi-B; 29 March 2013 at 03:40 PM.
Old 29 March 2013, 04:17 PM
  #15  
nyscooby
Scooby Regular
iTrader: (12)
 
nyscooby's Avatar
 
Join Date: Jun 2004
Location: Las Vegas
Posts: 1,785
Received 1 Like on 1 Post
Default

Glad to someone wants to help out a fellow owner..
Old 29 March 2013, 05:05 PM
  #16  
STEVEBOXER
Scooby Regular
 
STEVEBOXER's Avatar
 
Join Date: Aug 2011
Location: NORTH WALES
Posts: 646
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by tubbytommy
See yah then.
A bit harsh TT, you should get a job with the Samaritans lol.
Old 29 March 2013, 08:13 PM
  #17  
Mooburu
Scooby Regular
 
Mooburu's Avatar
 
Join Date: Sep 2010
Location: N.Wales
Posts: 95
Likes: 0
Received 0 Likes on 0 Posts
Default

If you're bleeding it everyday without progress, maybe it'd be best to take it to specialist and get the problem diagnosed?

Once it's sorted you'll soon enjoy it again, I always do after the f***ing thing breaks......until the next problem starts
Old 29 March 2013, 08:22 PM
  #18  
L.J.F
Instructing with fear
iTrader: (31)
 
L.J.F's Avatar
 
Join Date: Feb 2007
Location: Www.Extreme-rally.co.uk
Posts: 5,101
Likes: 0
Received 1 Like on 1 Post
Default

I would look at thermostat and radiator next!
Old 29 March 2013, 08:32 PM
  #19  
sunnyjones003
Scooby Regular
iTrader: (12)
 
sunnyjones003's Avatar
 
Join Date: May 2011
Location: Las Vegas on the roulette table
Posts: 1,303
Likes: 0
Received 0 Likes on 0 Posts
Default

hi mate, isnt indigo GT close to you, they work on subarus mate, might be a good idea to take it there fo a few hours
Old 29 March 2013, 08:43 PM
  #20  
buff01
Scooby Regular
 
buff01's Avatar
 
Join Date: Feb 2009
Location: south wales
Posts: 79
Likes: 0
Received 0 Likes on 0 Posts
Default

have you tried heater matrix slightly blocked, try flushing it out, played havoc with me years ago on a carlton I had,, by passed it and no probs again just a thought, hope you get it sorted
Old 29 March 2013, 08:43 PM
  #21  
yabbadoo4
Scooby Regular
iTrader: (8)
 
yabbadoo4's Avatar
 
Join Date: Mar 2011
Location: planet subaru
Posts: 3,245
Received 15 Likes on 13 Posts
Default

good to see some members with some helpful comments, restores the faith a bit.
Old 29 March 2013, 08:56 PM
  #22  
tubbytommy
BANNED
iTrader: (20)
 
tubbytommy's Avatar
 
Join Date: Mar 2010
Location: crawley :)
Posts: 16,950
Likes: 0
Received 1 Like on 1 Post
Default

Originally Posted by yabbadoo4
good to see some members with some helpful comments, restores the faith a bit.



the guy is having a rant, the original post i replied to has been edited somewhat.

no need to blame the car if you have no idea what you are doing and just guessing the fault.
Old 29 March 2013, 08:59 PM
  #23  
ae82mad
Scooby Regular
iTrader: (10)
 
ae82mad's Avatar
 
Join Date: Dec 2009
Posts: 956
Received 1 Like on 1 Post
Default

Originally Posted by tubbytommy
See yah then.
..

Last edited by ae82mad; 29 March 2013 at 09:02 PM.
Old 29 March 2013, 09:02 PM
  #24  
andervaliant
Scooby Newbie
iTrader: (1)
 
andervaliant's Avatar
 
Join Date: Feb 2011
Location: stoke on trent
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Default

I've just had similar problem with my bugeye ,
Turned out the pipe from coolant header tank to the expansion bottle was blocked solid , cleaned pipe out flushed system now no problems. Keep at it you'll get it sorted
Old 29 March 2013, 09:35 PM
  #25  
duds64
Scooby Regular
iTrader: (2)
 
duds64's Avatar
 
Join Date: Dec 2007
Posts: 224
Likes: 0
Received 0 Likes on 0 Posts
Default

have you tried by-passing the heater matrix?
Old 29 March 2013, 09:35 PM
  #26  
Tony Harrington
Scooby Regular
iTrader: (8)
 
Tony Harrington's Avatar
 
Join Date: Dec 2011
Location: Wigan
Posts: 1,928
Likes: 0
Received 1 Like on 1 Post
Default

Everybody who owns a Scoob at some point feels like you do at the mo mate. Just don't make any rash decision while your fired up or you may regret it.

Just take on some of the advice above & you'll get there bud.
Old 29 March 2013, 09:45 PM
  #27  
mickywrx
Unmapped 12.4s @ 105
iTrader: (29)
 
mickywrx's Avatar
 
Join Date: Apr 2005
Location: Newcastle. 330bhp-289lb/ft @ 1bar boost - 12.4s @ 105mph
Posts: 11,776
Likes: 0
Received 4 Likes on 4 Posts
Post

I've been calling my car a ******* **** on a monthly basis for 8 years, mainly over trivial things, detonated 3rd gears and stuff.

Persevere with it.
Old 29 March 2013, 09:51 PM
  #28  
Peedee
Scooby Regular
iTrader: (4)
 
Peedee's Avatar
 
Join Date: Jun 2009
Location: W / London
Posts: 2,168
Likes: 0
Received 0 Likes on 0 Posts
Default

I said I was getting rid back in 2010.








And here I am
Old 29 March 2013, 10:00 PM
  #29  
m_reed
Scooby Regular
iTrader: (1)
 
m_reed's Avatar
 
Join Date: Sep 2007
Posts: 135
Likes: 0
Received 0 Likes on 0 Posts
Default

Micky you are always calling someone or something a **** lmao
Old 29 March 2013, 10:12 PM
  #30  
buff01
Scooby Regular
 
buff01's Avatar
 
Join Date: Feb 2009
Location: south wales
Posts: 79
Likes: 0
Received 0 Likes on 0 Posts
Default

Believe mate don't get rid of :-) I just sold my wr1 & do I regret it oh yes I do,, try a few thing suggested first


Quick Reply: Had enough of subarus.



All times are GMT +1. The time now is 11:11 PM.