Non-starting scooby
06 July 2009, 10:46 PM
#1
Scooby Newbie
Thread Starter
Join Date: Sep 2007
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Non-starting scooby
I went to work this morning - car was fine. Came out of work after 2 hours, to go to next job, and it would turn over, but not fire. 
Called the AA, the chap was very good. Within about 15minutes, he knew it was lack of fuel. He looked at the electrics under the dash, to find out if it was the alarm interfering with the fuel pump, or the fuel pump itself, or something else.
After another 20mins or so, he knew exactly what it was. The connection block under the rear seat had started overheat and melt slightly, and one of the wires had a dodgy connection. He put a pair of blue terminal connectors on and now it runs fine
, but the block does need replacing. Apparently, this is not an uncommon problem.
Anyone else had this problem?
Called the AA, the chap was very good. Within about 15minutes, he knew it was lack of fuel. He looked at the electrics under the dash, to find out if it was the alarm interfering with the fuel pump, or the fuel pump itself, or something else.
After another 20mins or so, he knew exactly what it was. The connection block under the rear seat had started overheat and melt slightly, and one of the wires had a dodgy connection. He put a pair of blue terminal connectors on and now it runs fine
, but the block does need replacing. Apparently, this is not an uncommon problem.Anyone else had this problem?
07 July 2009, 10:01 PM
#4
Scooby Newbie
Thread Starter
Join Date: Sep 2007
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
It's a 1992 WRX impreza, Japanese import. The terminal block is underneath the rear seat, drivers side. The bottom half of the seat needs to be moved to see it.
Everybody should check to see if there's has started to melt. It might be possible to start a fire!
Everybody should check to see if there's has started to melt. It might be possible to start a fire!
08 July 2009, 08:49 AM
#5
Scooby Regular
Join Date: Sep 2004
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
Common fault on the classic apparently... I had a starting problem and the RAC checked it too... unfortunately He could not find the fault, it was the Cam sensor on my car which I cured after much cursing, expense and knuckle rash..... someone on here pointed me in the right direction and a cure.. sound as a pound now!
08 July 2009, 12:18 PM
#6
Mine's an 03 STi and I do have starting problems, which come and go!
I already had the rear squab out to locate a water leak, so I checked the connector, sprayed with elec. cleaner and re-connected anyway.
I've also had both crank and cam pos. sensors out, cleaned, magnet ok, but still have problems from time to time.
JohnD
I already had the rear squab out to locate a water leak, so I checked the connector, sprayed with elec. cleaner and re-connected anyway.
I've also had both crank and cam pos. sensors out, cleaned, magnet ok, but still have problems from time to time.
JohnD
08 July 2009, 01:35 PM
#7
Scooby Regular
Join Date: Oct 2000
Posts: 71
Likes: 0
Received 0 Likes
on
0 Posts
Common problem
Hello mate,
A common problem on the 1st series cars, not too sure about the later ones. Mine (94 WRX) got a lift home twice on recovery trucks before I sorted it out. Was the terminal block melting - job to find as well. I posted a bit about it at the time - some time ago now (4yrs ago + ?)
Mart.
A common problem on the 1st series cars, not too sure about the later ones. Mine (94 WRX) got a lift home twice on recovery trucks before I sorted it out. Was the terminal block melting - job to find as well. I posted a bit about it at the time - some time ago now (4yrs ago + ?)
Mart.
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM