Urgent Some Help and Adivce needed PLEASE
#1
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Jan 2007
Location: Swansea South Wales, UK.
Posts: 692
Likes: 0
Received 0 Likes
on
0 Posts
Urgent Some Help and Adivce needed PLEASE
Posting in here because this is where most peeps read.
Here it goes :-
Coming home from work joined the motorway this evening there was a gap to pull out into the fast lane so i put her in third put my foot down the car got to about 4.5k Revs and the car just died on me. The car at the time still had electrical power all the lights on the dash were alight and i hit the hazards on and pulled over to the hard shoulder.
First thoughts this is something bad, oh my god what am i going to do. Got out and had a check under the bonnet make sure all belts and everything were intact everything seemed fine so i bit the bullet and started her back up.Oh no 'Check Engine' warning light is on but the engine started. Its searching through the revs at idle and whilst on the move it seems like its missing now and again.
Got the car home turned it off, left it for about ten mins started her back up and she started first time. Check Engine warning light still on and its still searching all over the place.
After Reading so much about peoples MAF sensors being sensitive is this a good place to start ????
Forgot to mention the car is an X Reg Classic Turbo2000
Any help will be very much appreciated Melon.
Here it goes :-
Coming home from work joined the motorway this evening there was a gap to pull out into the fast lane so i put her in third put my foot down the car got to about 4.5k Revs and the car just died on me. The car at the time still had electrical power all the lights on the dash were alight and i hit the hazards on and pulled over to the hard shoulder.
First thoughts this is something bad, oh my god what am i going to do. Got out and had a check under the bonnet make sure all belts and everything were intact everything seemed fine so i bit the bullet and started her back up.Oh no 'Check Engine' warning light is on but the engine started. Its searching through the revs at idle and whilst on the move it seems like its missing now and again.
Got the car home turned it off, left it for about ten mins started her back up and she started first time. Check Engine warning light still on and its still searching all over the place.
After Reading so much about peoples MAF sensors being sensitive is this a good place to start ????
Forgot to mention the car is an X Reg Classic Turbo2000
Any help will be very much appreciated Melon.
Last edited by MisterMelon; 29 August 2007 at 06:54 PM. Reason: car details
#2
Scooby Regular
iTrader: (3)
Join Date: Aug 2004
Location: Muppetising life
Posts: 15,449
Likes: 0
Received 0 Likes
on
0 Posts
Not being a mechanic I cannot answer for sure, but I would not drive my car like that for any distance. You simply increase the chance of doing long term damage.
It could be the MAF, as a failure would bring up the CEL light, and make it run rough. It may be something else though...
It could be the MAF, as a failure would bring up the CEL light, and make it run rough. It may be something else though...
#3
Scooby Regular
iTrader: (1)
Scoobypedia | Trusted knowledge for everything Subaru | Scoobypedia browse tells you how to check for error codes.
Getting to 4500 revs sounds like limphome mode
Getting to 4500 revs sounds like limphome mode
#6
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Jan 2007
Location: Swansea South Wales, UK.
Posts: 692
Likes: 0
Received 0 Likes
on
0 Posts
I crawled home dare i say it on the hard shoulder, and its parked up on the drive and isn't going anywhere. Didn't fancy leaving on the side of the motorway.
#7
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Jan 2007
Location: Swansea South Wales, UK.
Posts: 692
Likes: 0
Received 0 Likes
on
0 Posts
Cheers for the quick replies, I found the connectors to run the self diagnostic test and it came up with error code 23 which on Scoobypedia states its the Mass Airflow Sensor Circuit (Cheers BlackWRX).
Looks like its a new MAF for me, but will the car remain in LimpMode when i replace the MAF? If so how will i return the car to its normal state ? Reset the ECU?
Cheers Melon
Looks like its a new MAF for me, but will the car remain in LimpMode when i replace the MAF? If so how will i return the car to its normal state ? Reset the ECU?
Cheers Melon
Trending Topics
#9
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Jan 2007
Location: Swansea South Wales, UK.
Posts: 692
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys cheers all for the quick response's i know i have already said that. I picked a new MAF up for the car today and its back up and running fine.
I love this website there is so much information to be found and there is so many helpful people here too, God knows how much i would of ended up spending if it had to go into a garage to have this Fixed.
Once again thanks guys Ryan.
I love this website there is so much information to be found and there is so many helpful people here too, God knows how much i would of ended up spending if it had to go into a garage to have this Fixed.
Once again thanks guys Ryan.
Thread
Thread Starter
Forum
Replies
Last Post
MH-Racing
Subaru Parts
18
18 October 2015 04:49 PM
robbie1988
Wanted
2
13 September 2015 09:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 06:51 PM