Drivers Electric Window Switch
#1
Scooby Regular
Thread Starter
Drivers Electric Window Switch
Hi all,
07Hawk STi.
Just been out, as I pushed down on the driver window switch and I thought I heard something snap / break....but just kind of ignored it I suppose....wasn't sure it was the switch.
Anyway, something has broken though as now there isn't such a defined line between being able to put the window up or down in stages, or up and down in auto.
Both functions work, but the switch now doesn't have the usual resistance between functions if you see what I mean.
I may take the whole assembly off the door card and see if I can fix anything obvious.....but is taking this assembly off just the one screw down in the door pull? It's got a small cover over it.
I can't see anything else fixing it on, maybe just also some trim clips?
Any advice would be coolio....
Many Thanks.
07Hawk STi.
Just been out, as I pushed down on the driver window switch and I thought I heard something snap / break....but just kind of ignored it I suppose....wasn't sure it was the switch.
Anyway, something has broken though as now there isn't such a defined line between being able to put the window up or down in stages, or up and down in auto.
Both functions work, but the switch now doesn't have the usual resistance between functions if you see what I mean.
I may take the whole assembly off the door card and see if I can fix anything obvious.....but is taking this assembly off just the one screw down in the door pull? It's got a small cover over it.
I can't see anything else fixing it on, maybe just also some trim clips?
Any advice would be coolio....
Many Thanks.
#2
Scooby Regular
Join Date: Apr 2013
Location: Berks
Posts: 4,224
Likes: 0
Received 0 Likes
on
0 Posts
Yeah it's just the screw under that cover and a metal Spring clip further forward. Dead easy to take out. Only problem being the switch assembly itself is really hard to come by (assuming it's the same as the Wrx).
#3
Scooby Regular
Thread Starter
Cheers dude. Yes, this is what worries me, pricey from a dealer, but not so bad if I can get just the one driver side switch, not needing the whole assembly......if it's silly money I'll just live with it.
#4
Scooby Regular
My one for a blob eye Widetrack sti was roughly £90 from a dealer, that was for the whole assembly
Last edited by nozzavtr; 30 January 2016 at 07:00 PM.
#5
Scooby Regular
Thread Starter
#6
Scooby Regular
As far as I'm aware it only comes in a whole unit. My drivers switch went completely, I couldn't even get the window up, thankfully the car is garaged and the new switch worked fine.
#7
Scooby Regular
To remove the plugs from the unit there's a small tab you need to push in to undo the clip, I couldn't work out how to do it and came on here for help!
Trending Topics
#10
Scooby Regular
Join Date: Apr 2013
Location: Berks
Posts: 4,224
Likes: 0
Received 0 Likes
on
0 Posts
Pretty much, all 4 switches are mounted to a single circuit board. You might be able to separate them if you're very (very) careful but I doubt you'll be able to buy a single switch.
#11
Scooby Regular
Thread Starter
Fixed.
Took off the assembly, undid the 3 screws that hold on the 4 Nissan switches module, then the cap for the drivers switch....prised it off gently.
Found a small triangular piece of plastic about 3mm tri...that had come off from "somewhere"
Managed to find out where it came from (the underside of the switch cap) so Gorilla glued it back and strengthened the join with Q-Bond granules, again mixed with Gorilla super glue.
Re-greased the little rocker bearings with Shell Retinax....all I had.
Put everything back together and the jobs a good-un. Just don't know for how long......
Thanks for all the input, much appreciated.
Took off the assembly, undid the 3 screws that hold on the 4 Nissan switches module, then the cap for the drivers switch....prised it off gently.
Found a small triangular piece of plastic about 3mm tri...that had come off from "somewhere"
Managed to find out where it came from (the underside of the switch cap) so Gorilla glued it back and strengthened the join with Q-Bond granules, again mixed with Gorilla super glue.
Re-greased the little rocker bearings with Shell Retinax....all I had.
Put everything back together and the jobs a good-un. Just don't know for how long......
Thanks for all the input, much appreciated.
Last edited by Hawkeye D; 31 January 2016 at 12:36 PM.
#12
Scooby Regular
Fixed.
Took off the assembly, undid the 3 screws that hold on the 4 Nissan switches module, then the cap for the drivers switch....prised it off gently.
Found a small triangular piece of plastic about 3mm tri...that had come off from "somewhere"
Managed to find out where it came from (the underside of the switch cap) so Gorilla glued it back and strengthened the join with Q-Bond granules, again mixed with Gorilla super glue.
Re-greased the little rocker bearings with Shell Retinax....all I had.
Put everything back together and the jobs a good-un. Just don't know for how long......
Thanks for all the input, much appreciated.
Took off the assembly, undid the 3 screws that hold on the 4 Nissan switches module, then the cap for the drivers switch....prised it off gently.
Found a small triangular piece of plastic about 3mm tri...that had come off from "somewhere"
Managed to find out where it came from (the underside of the switch cap) so Gorilla glued it back and strengthened the join with Q-Bond granules, again mixed with Gorilla super glue.
Re-greased the little rocker bearings with Shell Retinax....all I had.
Put everything back together and the jobs a good-un. Just don't know for how long......
Thanks for all the input, much appreciated.
Thread
Thread Starter
Forum
Replies
Last Post
morepatrols
Drivetrain
0
24 January 2016 09:15 PM
Mattybr5@MB Developments
Car Parts For Sale
0
24 January 2016 07:51 PM