Breaking 1998 UK. Power fc, PPG, Hyper twin, gt35R, 4 pot Brembo's ect
#1
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Breaking 1998 UK. Power fc, PPG, Hyper twin, gt35R, 4 pot Brembo's ect
Im Breaking a 1998 UK with bigish spec. All standard and lots of uprated parts available. I will post a full list of parts and some pics tomorow but in the mean time off the top of my head i have:
Apexi 3 plug Power FC with comander
Apexi AVCR limited edition Black
Exedy Hyper twin with ( 600 miles on it )
Tien super street coilovers
4 pot Gold Brembo's with good 5 X 100 PCD discs ( not much on pads )
Garrett GT-35R ( never run )
Turbosmart 48mm progate ( never run )
740cc injector with phase 2 to 1 convertion kit ( run for 600 miles )
Forged EJ20 closed deck block, full spec tomorow ( 600 miles on it )
HKS headers
PPG box 1-4 straight cut syncro UK 5th, billiet selector forks ( never turned a cog ) I have the prop and 3.9 rear diff to go with it.
lots more but my mind has gone blank.
Apexi 3 plug Power FC with comander
Apexi AVCR limited edition Black
Exedy Hyper twin with ( 600 miles on it )
Tien super street coilovers
4 pot Gold Brembo's with good 5 X 100 PCD discs ( not much on pads )
Garrett GT-35R ( never run )
Turbosmart 48mm progate ( never run )
740cc injector with phase 2 to 1 convertion kit ( run for 600 miles )
Forged EJ20 closed deck block, full spec tomorow ( 600 miles on it )
HKS headers
PPG box 1-4 straight cut syncro UK 5th, billiet selector forks ( never turned a cog ) I have the prop and 3.9 rear diff to go with it.
lots more but my mind has gone blank.
Last edited by al125; 08 October 2010 at 01:24 AM. Reason: more info
Trending Topics
#8
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Hi guys, sorry the is no full list up yet with pic and prices. Finshed work late today and then put new floor in the living room so had to unplug modem, Floor went in well but tring to get the modem and router back up and running was another story. I am pulling this car apart tomorow and will have every thing up and priced then. I will reply to all PM's as soon as i can.
#9
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Right guys im with this car and starting to break it now. Parts, prices and pics will be going up today. All pm's will be replied to by tonight. If the is anything you want off the car i will be checking this post through out the day and can give you an answer straight away.
#10
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Engine is a 2.0L EJ20:
Standard center thrust crank
ACL Duraglide 780 Bearings
Lateral/Crower custom H section rod set 2.0lt
Lateral/Wiseco Custom 2.0lt 92.5mm '92-'98 Forged Piston
Metal head gasket from lateral performance.
head stud kit (either arp or api 14 mm i cant remember but i can pull rocker cover off and check if needed )
new timeing belt kit , new water pump , new oil pump and all gaskets and seals replaced 600 miles ago when engine was built. Im am after £1800
Last edited by al125; 09 October 2010 at 05:46 PM. Reason: edited to add price
#11
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
The 35R has a .82 exhaust housing. All the pipe work needed to make it work is here along with a front mounted intercool. Wastegate is on a V band but with the car not being fished was never fitted. All the weld in collers are here so it just needs putting in the up pipe and job done. I will put a price up later for this as im about to take the engine and box out and can not think ATM.
#15
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Right i have pulled alot of the car apart today, engine and gearbox are out and pics of all listed parts will be up later. I gues it's about time to put some prices up then.
Apexi 3 plug Power FC and comander for v3/v4 96-98. Great condition
and come off a running car. £600
Complet and working Apexi limited addition black AVCR, small scratch
on screen but other than that mint condition. £450
4 pot gold Brembos in good condition with good 5X100 pcd discs
( not much left on pads ) £600
Genuine HKS headers / tubular manifold. no up pipe as it was choped
to fit another turbo. Standard 2 bolt up pipe will fit or the HKS one
can be bought seperately. good condition loocking for £400
Tein super street coilovers with standard top mount in good condition.
All ajust as they should and have very little or no corrosion. £500
Nismo/Tomei 740cc phase Two side feed injectors flow mached by
Mark at lateral and come with a phase 2 to 1 convesion kit. these
have only done 600 miles on a new build and are as new. £350
Exedy hyper twin clutch with only 600 miles on a newly build engine
so this clutch is in great condition with relese bearing. £750
Brand new PPG 1-4 straight cut syncro gear box. it has the normal
uk 5th with a 3.9 front diff 1:1 drop gears and comes with a prop
shaft and 3.9 rear diff. the box was built with all new seals, bearings
and billet selector forks. it is built into a TY752 case with brand
new reverse switch and speedo sensor. this box has not turned
a cog. £3000
Brand new never run garrett GT35R with .82 exhaust housing. Non
ported shroud sorry guys. £800
Turbo smart 48mm progate external waste gate with all weld in
collors and V band clamps. Brand new never fitted SOLD
The engine was built by dp motorsport
Engine is a 2.0L EJ20:
Standard center thrust crank
ACL Duraglide 780 Bearings
Lateral/Crower custom H section rod set 2.0lt
Lateral/Wiseco Custom 2.0lt 92.5mm '92-'98 Forged Piston
Metal head gasket from lateral performance.
head stud kit (either arp or api 14 mm i cant remember but i can
pull rocker cover off and check if needed )
new timeing belt kit , new water pump , new oil pump and all
gaskets and seals replaced 600 miles ago when engine was built.
Im am after £1800
Thats it for now but pics to go up and more stuff to be listed. I am
open to offers on all of the above but please keep it sensible.
Apexi 3 plug Power FC and comander for v3/v4 96-98. Great condition
and come off a running car. £600
Complet and working Apexi limited addition black AVCR, small scratch
on screen but other than that mint condition. £450
4 pot gold Brembos in good condition with good 5X100 pcd discs
( not much left on pads ) £600
Genuine HKS headers / tubular manifold. no up pipe as it was choped
to fit another turbo. Standard 2 bolt up pipe will fit or the HKS one
can be bought seperately. good condition loocking for £400
Tein super street coilovers with standard top mount in good condition.
All ajust as they should and have very little or no corrosion. £500
Nismo/Tomei 740cc phase Two side feed injectors flow mached by
Mark at lateral and come with a phase 2 to 1 convesion kit. these
have only done 600 miles on a new build and are as new. £350
Exedy hyper twin clutch with only 600 miles on a newly build engine
so this clutch is in great condition with relese bearing. £750
Brand new PPG 1-4 straight cut syncro gear box. it has the normal
uk 5th with a 3.9 front diff 1:1 drop gears and comes with a prop
shaft and 3.9 rear diff. the box was built with all new seals, bearings
and billet selector forks. it is built into a TY752 case with brand
new reverse switch and speedo sensor. this box has not turned
a cog. £3000
Brand new never run garrett GT35R with .82 exhaust housing. Non
ported shroud sorry guys. £800
Turbo smart 48mm progate external waste gate with all weld in
collors and V band clamps. Brand new never fitted SOLD
Engine is a 2.0L EJ20:
Standard center thrust crank
ACL Duraglide 780 Bearings
Lateral/Crower custom H section rod set 2.0lt
Lateral/Wiseco Custom 2.0lt 92.5mm '92-'98 Forged Piston
Metal head gasket from lateral performance.
head stud kit (either arp or api 14 mm i cant remember but i can
pull rocker cover off and check if needed )
new timeing belt kit , new water pump , new oil pump and all
gaskets and seals replaced 600 miles ago when engine was built.
Im am after £1800
Thats it for now but pics to go up and more stuff to be listed. I am
open to offers on all of the above but please keep it sensible.
Last edited by al125; 11 October 2010 at 12:49 AM.
#21
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
Yes mate im open to offers but if you have alreay looked into a PPG gear set and building it into a gear box with new bearings and seals then you know what it would cost so keep the offers sensible please. Rember i will supply the correct prop and rear diff to run with it.
#22
Scooby Regular
Thread Starter
iTrader: (2)
Join Date: Jan 2005
Posts: 352
Likes: 0
Received 0 Likes
on
0 Posts
It is 100% genuine Garrett turbo bought from AET Turbos. I think it is the GT3582R - 714568 - 2 but i will have to check. It definitely has a T3 turbine inlet flange and 4-bolt turbine outlet flange with a 0.82 exhaust housing and a AR 0.70 cold side but i will have to check on the rest. Iwill try and put some more pics up later.
Last edited by al125; 10 October 2010 at 06:36 PM.