Breaking 1998 UK. Power fc, PPG, Hyper twin, gt35R, 4 pot Brembo's ect
 

Im Breaking a 1998 UK with bigish spec. All standard and lots of uprated parts available. I will post a full list of parts and some pics tomorow but in the mean time off the top of my head i have:

Apexi 3 plug Power FC with comander
Apexi AVCR limited edition Black
Exedy Hyper twin with ( 600 miles on it )
Tien super street coilovers
4 pot Gold Brembo's with good 5 X 100 PCD discs ( not much on pads )
Garrett GT-35R ( never run )
Turbosmart 48mm progate ( never run )
740cc injector with phase 2 to 1 convertion kit ( run for 600 miles )
Forged EJ20 closed deck block, full spec tomorow ( 600 miles on it )
HKS headers
PPG box 1-4 straight cut syncro UK 5th, billiet selector forks ( never turned a cog ) I have the prop and 3.9 rear diff to go with it.
lots more but my mind has gone blank.

hi mate can you stick some prices on there please

Yeh sorry, prices would be handy. I will get them up tomorow with a full list. All pm's replied to.

i'm interested in engine pending spec and price.

who built the engine?

Hi matey interested in the new 35R depending on size and price and also the wastegate is it v-band ?
Do you have the twisted pipework kit to suite the turbo ?

have you got the blanking plates for under the bonnet vents mate?

Price on gearbox and diff please

Hi guys, sorry the is no full list up yet with pic and prices. Finshed work late today and then put new floor in the living room so had to unplug modem, Floor went in well but tring to get the modem and router back up and running was another story. I am pulling this car apart tomorow and will have every thing up and priced then. I will reply to all PM's as soon as i can.

Right guys im with this car and starting to break it now. Parts, prices and pics will be going up today. All pm's will be replied to by tonight. If the is anything you want off the car i will be checking this post through out the day and can give you an answer straight away.

The engine was built by dp motorsport

Engine is a 2.0L EJ20:
Standard center thrust crank

ACL Duraglide 780 Bearings

http://lateralperformance.co.uk/shop...beam%20rod.jpg Lateral/Crower custom H section rod set 2.0lt

http://lateralperformance.co.uk/shop...l/awaiting.gif Lateral/Wiseco Custom 2.0lt 92.5mm '92-'98 Forged Piston

Metal head gasket from lateral performance.
head stud kit (either arp or api 14 mm i cant remember but i can pull rocker cover off and check if needed )
new timeing belt kit , new water pump , new oil pump and all gaskets and seals replaced 600 miles ago when engine was built. Im am after £1800

The 35R has a .82 exhaust housing. All the pipe work needed to make it work is here along with a front mounted intercool. Wastegate is on a V band but with the car not being fished was never fitted. All the weld in collers are here so it just needs putting in the up pipe and job done. I will put a price up later for this as im about to take the engine and box out and can not think ATM.

Just some pics to give you an idea.

http://i3.photobucket.com/albums/y60...1/DSC00829.jpg

http://i3.photobucket.com/albums/y60...1/DSC00830.jpg

http://i3.photobucket.com/albums/y60...1/DSC00832.jpg

http://i3.photobucket.com/albums/y60...1/DSC00835.jpg

http://i3.photobucket.com/albums/y60...1/DSC00839.jpg

http://i3.photobucket.com/albums/y60...1/DSC00841.jpg

http://i3.photobucket.com/albums/y60...1/DSC00842.jpg

http://i3.photobucket.com/albums/y60...1/DSC00844.jpg

££££££££££ ?

Interested in clutch ,pm sent

Right i have pulled alot of the car apart today, engine and gearbox are out and pics of all listed parts will be up later. I gues it's about time to put some prices up then.

Apexi 3 plug Power FC and comander for v3/v4 96-98. Great condition
and come off a running car. £600

Complet and working Apexi limited addition black AVCR, small scratch
on screen but other than that mint condition. £450

4 pot gold Brembos in good condition with good 5X100 pcd discs
( not much left on pads ) £600

Genuine HKS headers / tubular manifold. no up pipe as it was choped
to fit another turbo. Standard 2 bolt up pipe will fit or the HKS one
can be bought seperately. good condition loocking for £400

Tein super street coilovers with standard top mount in good condition.
All ajust as they should and have very little or no corrosion. £500

Nismo/Tomei 740cc phase Two side feed injectors flow mached by
Mark at lateral and come with a phase 2 to 1 convesion kit. these
have only done 600 miles on a new build and are as new. £350

Exedy hyper twin clutch with only 600 miles on a newly build engine
so this clutch is in great condition with relese bearing. £750

Brand new PPG 1-4 straight cut syncro gear box. it has the normal
uk 5th with a 3.9 front diff 1:1 drop gears and comes with a prop
shaft and 3.9 rear diff. the box was built with all new seals, bearings
and billet selector forks. it is built into a TY752 case with brand
new reverse switch and speedo sensor. this box has not turned
a cog. £3000

Brand new never run garrett GT35R with .82 exhaust housing. Non
ported shroud sorry guys. £800

Turbo smart 48mm progate external waste gate with all weld in
collors and V band clamps. Brand new never fitted SOLD

The engine was built by dp motorsport

Engine is a 2.0L EJ20:
Standard center thrust crank

ACL Duraglide 780 Bearings

http://lateralperformance.co.uk/shop...beam%20rod.jpg Lateral/Crower custom H section rod set 2.0lt

http://lateralperformance.co.uk/shop...l/awaiting.gif Lateral/Wiseco Custom 2.0lt 92.5mm '92-'98 Forged Piston

Metal head gasket from lateral performance.
head stud kit (either arp or api 14 mm i cant remember but i can
pull rocker cover off and check if needed )
new timeing belt kit , new water pump , new oil pump and all
gaskets and seals replaced 600 miles ago when engine was built.
Im am after £1800

Thats it for now but pics to go up and more stuff to be listed. I am
open to offers on all of the above but please keep it sensible.

hi mate interested in turbo and wastegate you have pm

PM sent re clutch. where you located?

hi mate are you open to offers on the ppg gearbox???? cheers. jay

also any more pics of turbo ???? i.e numbers on the side is it a genuine garrett ????

Sorry mate not got them.

Yes mate im open to offers but if you have alreay looked into a PPG gear set and building it into a gear box with new bearings and seals then you know what it would cost so keep the offers sensible please. Rember i will supply the correct prop and rear diff to run with it.

It is 100% genuine Garrett turbo bought from AET Turbos. I think it is the GT3582R - 714568 - 2 but i will have to check. It definitely has a T3 turbine inlet flange and 4-bolt turbine outlet flange with a 0.82 exhaust housing and a AR 0.70 cold side but i will have to check on the rest. Iwill try and put some more pics up later.

sorry..

just in the middle of replying to your PM mate

SOLD

http://i3.photobucket.com/albums/y60...01010-1930.jpg

http://i3.photobucket.com/albums/y60...01010-1931.jpg

http://i3.photobucket.com/albums/y60...01010-1931.jpg

I will have to take more pics of the turbo tomorow.

All PM's replied to.

i will have the wastegate mate get some more pics of the turbo and i might have that too pending on the price we can agree cheers

pm sent about injectors :thumb:

pm replied to.

you have pm