Silicone
#1
Silicone
Guys
I'll askin here, since DIY is generally pretty dead
I had to fit a new drain to the bathroom sink
During testing, it leaked probably due to the crap almost plastic like seal on the basin side, so I put a little bed of silicone in and then fitted it
How long realistically does silicone take to dry - the tube said 24 hours
Surely it must dry faster than that?
Cheers
I'll askin here, since DIY is generally pretty dead
I had to fit a new drain to the bathroom sink
During testing, it leaked probably due to the crap almost plastic like seal on the basin side, so I put a little bed of silicone in and then fitted it
How long realistically does silicone take to dry - the tube said 24 hours
Surely it must dry faster than that?
Cheers
Trending Topics
#8
Scooby Regular
iTrader: (2)
Silicone?
I can NEVER understand why folk use the stuff except for what it's designed: a sealant for around baths, sinks etc.
It's NOT designed for use as you have described. You want to hope you never need the joint off again, since silicone doesn't give easily.
The best stuff to use would have been something like this:http://www.google.co.uk/products/cat...ed=0CGUQ8wIwAQ
Non-setting, but seals perfectly. If you HAVE to open the joint again, you will be able to.
Screwfix sell it, as will any decent plumber's merchants.
I can NEVER understand why folk use the stuff except for what it's designed: a sealant for around baths, sinks etc.
It's NOT designed for use as you have described. You want to hope you never need the joint off again, since silicone doesn't give easily.
The best stuff to use would have been something like this:http://www.google.co.uk/products/cat...ed=0CGUQ8wIwAQ
Non-setting, but seals perfectly. If you HAVE to open the joint again, you will be able to.
Screwfix sell it, as will any decent plumber's merchants.
#9
Should I have put the stuff on both sides then?
I only put it on the bottom of the rubber/plastic seal
Alcazar - with plumbers mait, should one put this on both sides of the rubber seal?
I have a tiny leak today, but it looks like its on the waste pipe connection into the sink drain
I only put it on the bottom of the rubber/plastic seal
Alcazar - with plumbers mait, should one put this on both sides of the rubber seal?
I have a tiny leak today, but it looks like its on the waste pipe connection into the sink drain
#11
Scooby Senior
Yes, both sides of the rubber/plastic washer and on the metal flange that seals against the basin.
I hate plumbers mait, it's a pain to work with and I have taken a few out that have been siliconed in, no big deal tbh.
Check with some tissue to see where it is leaking, start at the top and keep checking it to see where it is damp, it'll probobly be coming down the threads and onto the trap.
I hate plumbers mait, it's a pain to work with and I have taken a few out that have been siliconed in, no big deal tbh.
Check with some tissue to see where it is leaking, start at the top and keep checking it to see where it is damp, it'll probobly be coming down the threads and onto the trap.
#13
Scooby Regular
Join Date: Feb 1999
Location: Cardiff. Wales
Posts: 11,758
Likes: 0
Received 0 Likes
on
0 Posts
Should I have put the stuff on both sides then?
I only put it on the bottom of the rubber/plastic seal
Alcazar - with plumbers mait, should one put this on both sides of the rubber seal?
I have a tiny leak today, but it looks like its on the waste pipe connection into the sink drain
I only put it on the bottom of the rubber/plastic seal
Alcazar - with plumbers mait, should one put this on both sides of the rubber seal?
I have a tiny leak today, but it looks like its on the waste pipe connection into the sink drain
#14
Scooby Regular
iTrader: (2)
I've done loads of plumbing, both here and in France......French stuff is quite expensive, and where we have 15mm and 22mm pipes, theirs are 8, 10, 12, 14 16 18 and 20mm. Connections are therefore an utter minefield
Pipe THICKNESS is always 1mm, so that a 14mm pipe slides inside a 16mm, and can then be soldered.
Many joints there are brazed, or even silver soldered due to higher pressures, mine is around 6bar.
Newer installations use PE tubing, either on it's own, or ina flexible conduit, red for hot, blue for cold. Cheap and easy, but the joints are wickedly expensive.
Pipe THICKNESS is always 1mm, so that a 14mm pipe slides inside a 16mm, and can then be soldered.
Many joints there are brazed, or even silver soldered due to higher pressures, mine is around 6bar.
Newer installations use PE tubing, either on it's own, or ina flexible conduit, red for hot, blue for cold. Cheap and easy, but the joints are wickedly expensive.
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM
blockhead
Subaru Parts
19
07 November 2015 11:50 PM