Amateur Radio People on here?
03 December 2003, 09:47 PM
#1
Scooby Regular
Thread Starter
Join Date: Jan 2002
Posts: 1,553
Likes: 0
Received 0 Likes
on
0 Posts
is there any of you on here that would be interested in buying this?
MA-550 Tower.
It is sold as seen and has not been used for several years.
No reserve, buyer must collect before December 22.
More information can be found on www.ustower.com
US Tower Corporation
Manufacturer of the World's Finest,
State of the Art,
Steel Telescoping Towers
1220 N. Marcin St. ~ Visalia, CA 93291
Phone: (559) 733-2438 ~ Fax: (559) 733-7194
US Tower Corp. makes our tubular tower series in 4 different sizes with a variety of accessories available to customize your installation.
The premier MA-Series crank-up Tubular Towers are designed to be both safe and neighbor friendly. The slender design gives a clean flagpole like appearance while allowing antennas from 12.7 to 19.4 sq. feet in 50 mph winds, depending upon the model. Uniform Building Code calculations are available from our office.
The MA-40 and 550 models come standard with flat base, wall bracket and rotor mast. No guying is required when the tower is properly bracketed to the eve of your house or building.
MA-Series towers are completely self-supporting only when used with MARB or MAB series bases. The MARB series rotor base allows the entire tower and antenna to be rotated from the base (rotor not included). This provides for easy rotor maintenance plus emergency hand rotation of the entire tower and antenna.
The MA-550MDP, 770MDP and 850MDP models include a heavy duty motor drive with positive pull down. The MDP models provide motorized raising and lowering of the tower. A remote control unit (RMC-1000) accessory is available that allows raising and lowering from your ham shack or other remote location.
All models without motor drives come standard with manual hand winches that have load actuated brakes for maximum safety. This feature prevents the winch from free-wheeling and causing injury to you or your installation in the event that you loose your grip during raising or lowering.
All steel used at US Tower conforms to ASTM specifications. All welding is done by certified factory personnel. All of our towers are factory tested by trained personnel before leaving the plant.
MA-550 Tower.
It is sold as seen and has not been used for several years.
No reserve, buyer must collect before December 22.
More information can be found on www.ustower.com
US Tower Corporation
Manufacturer of the World's Finest,
State of the Art,
Steel Telescoping Towers
1220 N. Marcin St. ~ Visalia, CA 93291
Phone: (559) 733-2438 ~ Fax: (559) 733-7194
US Tower Corp. makes our tubular tower series in 4 different sizes with a variety of accessories available to customize your installation.
The premier MA-Series crank-up Tubular Towers are designed to be both safe and neighbor friendly. The slender design gives a clean flagpole like appearance while allowing antennas from 12.7 to 19.4 sq. feet in 50 mph winds, depending upon the model. Uniform Building Code calculations are available from our office.
The MA-40 and 550 models come standard with flat base, wall bracket and rotor mast. No guying is required when the tower is properly bracketed to the eve of your house or building.
MA-Series towers are completely self-supporting only when used with MARB or MAB series bases. The MARB series rotor base allows the entire tower and antenna to be rotated from the base (rotor not included). This provides for easy rotor maintenance plus emergency hand rotation of the entire tower and antenna.
The MA-550MDP, 770MDP and 850MDP models include a heavy duty motor drive with positive pull down. The MDP models provide motorized raising and lowering of the tower. A remote control unit (RMC-1000) accessory is available that allows raising and lowering from your ham shack or other remote location.
All models without motor drives come standard with manual hand winches that have load actuated brakes for maximum safety. This feature prevents the winch from free-wheeling and causing injury to you or your installation in the event that you loose your grip during raising or lowering.
All steel used at US Tower conforms to ASTM specifications. All welding is done by certified factory personnel. All of our towers are factory tested by trained personnel before leaving the plant.
Thread
Thread Starter
Forum
Replies
Last Post
