Clifford 650 mk2 alarm will not turn of by fob is there another way to turn it off.
Managed to get the Clifford wizard to connect to lap top but get the message alarm need switching off, fob doesn't seem to be working.

 

u can turn it off by using the "plain switch" (mine is a toggle switch just behind the hand-brake) - but u need the code...............

have u only got one fob ????

 

Have 2 fobs, both wont work they did but something happend a long the way of building the car up.
Thought if I bought the wizard it would help switch a few things off. but alarm needs to be disarmed
before wizard can get into the system

 

You'll need the PIN number mate (4 digit code) that you enter into the plain switch. Personally I'd contacting Clifford UK for free advice

 

Where do you put the pin code in

 

You should have something like this


mine can bee seen just below the rpm dial on my dash


guide can be found here (see page 28)http://www.directeddealers.com/manua...730P_01-07.pdf

 

i had window probs with my alarm, like darms said you need the pin code. this will be in the users guide book if you have it.( comes in a small blue clifford plasic wallet ) and you tap that code into the two button pad like above.
i never had to do it as i sorted the problem out.
let me know if you want me to dig it out and send you a pic of the info?
but you will still need your unique 4 digit pin code?

 

You may well need a dealer/installer to look at the system as (like mine) the 4 digit number on the back of the book no longer applies as ive had it changed.

Tony

 

had what changed m8

 

there a 4 digit code scratched on the back of the alarm 7695 that should be it.
Only kidding about the code its not mine, thought ide better say before i get slaughtered lol

 

So is it one digit on one button and the next digit on the other button so on

 

One digit then the other button is the enter etc.
Example is 1234, its the top button 1 then the bottom button once, then 2 on the top, once on the bottom, 3 on the top, once on the bottom, 4 on the top, once on the bottom and you should see the light light up on the alarm indicator (that nice blue button with clifford on it)

Tony

 

mines sets but alarm goes off after 30 seconds or so..been sat in garage a few months with no battery in car..cant seem to find my wee pad for putting pin in..car starts runs sound but if alarms set closes windows an stuff n chirps but alarm goes off

 

Can you not just turn the ignition on then disconnect the battery to disarm?

 

No as it has a low voltage warning and battery backup.

Tony

 

Would this not put it into valet mode? or does that only work when the alram is not activated and/or on older alarms?

Or am I just wrong altogether... sure my old Cobra alarm had to be disconnected this way to disarm when the battery was low and caused it to go off.

 

Dose any body have a 0 in the valet code, will help me work out which it is of the back of alarm

 

@ slab, sorry mate aint checked this thread for a while.
if you dont have the little clifford book, i can scan it and send it to you.
the code is on the back of the book. ( but i aint gonna send you my code lol )
let me know if this will help you out?
im sure clifford must have a standard code to use, like with mobile phones...

 

shugsterc, you can buy the pad for a few quid.
well worth to have it as it activates blakjax etc.

 

Anyting that might help m8 would be appreciated

 

Pad do you mean the valet pad managed to drop on a new concept 500 brand new so use the pad, led and siren.
Ps if anyone wanting a cheap £35+£4 p&p brand new Clifford concept 500 check my ads

 

the default valet code for Cliffords alarms is (((((( Check yr PM;s )))))

 

@ slab emails sent mate, and yeah the pad meaning the one with two small buttons on it.

 

cheers m8 had a go to day did something because the alarm went off, tried to get the wizard on wont connect something about port name wrong cant find port1 port 2.3 not found.
Good job i don't drink or ide of been on the port the day i have, trying to get his dam wizard to connect, managed to get it on last time but alarm needed to be turned off

 

Still no joy with this wont turn off with valet nothing happens ,the fobs are like new when any button is pressed there's nothing as iif the fobs from another alarm but it has work before doing my nut in:ma d:

 

are u happy that u are entering to code correctly ??

Key in the ignition - turn to the 'fully' on position - then follow tony's instructions above

 

the light flashing 3 secs intervals will give it another go also shouldn't the fobs work Eva way, Is it possible I've messed the fob single up pressing buttons

 

@slab, whereabouts in the country are you.

 

SLAB -- if this is of any help to you - Check your PM's !!

 

was going to suggest removing that from public view.