Morette Wiring question
#1
Scooby Regular
Thread Starter
Join Date: Mar 1999
Location: The Great White North
Posts: 25,080
Likes: 0
Received 0 Likes
on
0 Posts
ok, hopefullt the last morette question I'll post
well, just got the morettes, and they look really nice. got one question though. there are two wires coming off the relay (for switching full beams?) a blue wire and a grey wire. The instructions indicate that these need to be spliced into the headlight loom.
My question is, what wires on the headlight loom does the brown wire connect to and which one does the blue wire connect to?
bear in mind that my car is a MY94 WRX so the headlight loom might be different (is it?)
thanks for any advice
well, just got the morettes, and they look really nice. got one question though. there are two wires coming off the relay (for switching full beams?) a blue wire and a grey wire. The instructions indicate that these need to be spliced into the headlight loom.
My question is, what wires on the headlight loom does the brown wire connect to and which one does the blue wire connect to?
bear in mind that my car is a MY94 WRX so the headlight loom might be different (is it?)
thanks for any advice
#2
Scooby Regular
Thread Starter
Join Date: Mar 1999
Location: The Great White North
Posts: 25,080
Likes: 0
Received 0 Likes
on
0 Posts
Getting bit closer here. have looked at the headlamp connector and it's got three wires, black, green and white, so all I need to know is which one do I plug the blue into and which the grey?
what's the worst I could do if I hit the wrong combo? blow a fuse/relay/bulb?
what's the worst I could do if I hit the wrong combo? blow a fuse/relay/bulb?
#5
Scooby Regular
Thread Starter
Join Date: Mar 1999
Location: The Great White North
Posts: 25,080
Likes: 0
Received 0 Likes
on
0 Posts
Pete,
thanks, I look forwared to hearing back from you. I'm just about to go and test fit them now, so it'll probsbly be quite a few hours before I'm ready to wire them up
thanks, I look forwared to hearing back from you. I'm just about to go and test fit them now, so it'll probsbly be quite a few hours before I'm ready to wire them up
#6
Scooby Regular
Thread Starter
Join Date: Mar 1999
Location: The Great White North
Posts: 25,080
Likes: 0
Received 0 Likes
on
0 Posts
Pete,
took the plunge and crossed as many apendages as possible and actually followed the instructions, which seemed to be correct, hey presto, working full beams.
must say the car looks really nice now. plus the 'gap' is nowhere near as bad as I though it'd be.
thanks for all your help and advice on this.
took the plunge and crossed as many apendages as possible and actually followed the instructions, which seemed to be correct, hey presto, working full beams.
must say the car looks really nice now. plus the 'gap' is nowhere near as bad as I though it'd be.
thanks for all your help and advice on this.
#7
Scooby Regular
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Markus,
No prob m8, glad it worked out
Took som pix on Sat 4 the site but they were pretty crap and
didn`t really highlight what i was trying to show
I`m gonna redo the pix real soon an up them to my site.
Ner mind though as long as u got em working. Glad i could be
of help.
L8r m8
Pete
No prob m8, glad it worked out
Took som pix on Sat 4 the site but they were pretty crap and
didn`t really highlight what i was trying to show
I`m gonna redo the pix real soon an up them to my site.
Ner mind though as long as u got em working. Glad i could be
of help.
L8r m8
Pete
Thread
Thread Starter
Forum
Replies
Last Post
shorty87
Full Cars Breaking For Spares
19
22 December 2015 11:59 AM
Brzoza
Engine Management and ECU Remapping
1
02 October 2015 05:26 PM