97 ECU PIN OUT Diagram???????????
#1
Hi All
Hope you can help again.
I have been trying to fit the AFR meter that i bought a while back and to no avail.
I have wired it using this set of pin out diagram's for a R reg 97 Catalunya, we don't seem to be getting any power at the desinated terminal for 12 volt source/ oxygen soucre.
Before you ask the Lamba Sensor is deffo working.
Seem Turbo Sport isn't letting me put up the Pin out Diagrams then!!!!!!!!
Cheers For all your Help.
Dougie
[Edited by dougies549 - 5/6/2003 11:16:51 PM]
Hope you can help again.
I have been trying to fit the AFR meter that i bought a while back and to no avail.
I have wired it using this set of pin out diagram's for a R reg 97 Catalunya, we don't seem to be getting any power at the desinated terminal for 12 volt source/ oxygen soucre.
Before you ask the Lamba Sensor is deffo working.
Seem Turbo Sport isn't letting me put up the Pin out Diagrams then!!!!!!!!
Cheers For all your Help.
Dougie
[Edited by dougies549 - 5/6/2003 11:16:51 PM]
#2
Scooby Regular
I though it stated in the distructions that it should be Engine earth, I bolted mine on to the block!
I don't remember where I took the +ive from orry, but any good ingnition 12v should do.
30 min is plenty, I fitted one to a mates car and we couldn't figure out why it wouldn't display, we'd been out to the dual carrage way a couple of times and the car was fully warm. The next day he rang on his way to work and it had come on and now the diplay comes on after a couple of minutes everytime.
Hope you get it sorted
I don't remember where I took the +ive from orry, but any good ingnition 12v should do.
30 min is plenty, I fitted one to a mates car and we couldn't figure out why it wouldn't display, we'd been out to the dual carrage way a couple of times and the car was fully warm. The next day he rang on his way to work and it had come on and now the diplay comes on after a couple of minutes everytime.
Hope you get it sorted
#3
Scooby Regular
The Earth should be "engine earth" and the signal wire you are splicing into is Pin 5 on the lowest plug (thick white wire)????
The signal will ulse from 0 volts to 0.7v when the engine is warm and idling, usually needs a good run to start it working for the first time though.
[Edited by Dyney - 5/6/2003 11:29:58 PM]
The signal will ulse from 0 volts to 0.7v when the engine is warm and idling, usually needs a good run to start it working for the first time though.
[Edited by Dyney - 5/6/2003 11:29:58 PM]
#4
Hi Dyney
Yeh it seem's that we have wired it correctly then, we earthed it to the battery as stated.
Where did you take your positive from?????????
When u say that you need to take it for a bit of a run to get it working for the first time what is meant by this?? Is for example 30-35 minute's good enought for this to get it working.
Cheers Dougie
Cheers for the help.
[Edited by dougies549 - 5/7/2003 7:43:29 PM]
Yeh it seem's that we have wired it correctly then, we earthed it to the battery as stated.
Where did you take your positive from?????????
When u say that you need to take it for a bit of a run to get it working for the first time what is meant by this?? Is for example 30-35 minute's good enought for this to get it working.
Cheers Dougie
Cheers for the help.
[Edited by dougies549 - 5/7/2003 7:43:29 PM]
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
Flat4x4-again
General Technical
2
29 September 2015 06:32 PM
MightyArsenal
Wheels, Tyres & Brakes
6
25 September 2015 08:31 PM