Any interest in new Alloy brake bells?
#1
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
Any interest in new Alloy brake bells?
I'm sure I can offer very good price's on these for a group buy , will change the look of your car and we can anodize any of the following colours,... black / blue / red / gold / sliver /purple / green
Ford ones but will look pretty much the same
If we get any interest , I will need to know some size's
Ford ones but will look pretty much the same
If we get any interest , I will need to know some size's
#5
Scooby Regular
Join Date: Jan 2006
Location: Wellingborough
Posts: 1,107
Likes: 0
Received 0 Likes
on
0 Posts
Once you have a set of bells you can buy any rotors you like to fit them AP Performance friction etc.
295mm rotors for subaru 4 pot
325mm rotors for brembo's
295mm rotors for subaru 4 pot
325mm rotors for brembo's
Last edited by finchyboy; 29 January 2009 at 10:44 PM.
#7
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
As above, and performance fricton supply just the replacement rotors for around £100 less than a full kit .
Our bells can be anodised any colour rather than standard colours you will normally get , and would have a better finish than most
If we can get a few interest they would be around £35+vat ea
Our bells can be anodised any colour rather than standard colours you will normally get , and would have a better finish than most
If we can get a few interest they would be around £35+vat ea
Trending Topics
#11
Former Sponsor
Thread Starter
iTrader: (49)
Join Date: Jan 2008
Posts: 3,222
Likes: 0
Received 0 Likes
on
0 Posts
CrazyGTiR - these don't fit any at the moment, need to gather sizes then make them
Stalked! - Ksports wouldnt be a problem, as you know I have them here and can easy get the size's, not sure if you have noticed but the bells on the ksports are a bit grainy and don't have a very good finish.
chrisdicko - will see what I can find, I can confirm I can get ksport and performance friction size's easy enough
Stalked! - Ksports wouldnt be a problem, as you know I have them here and can easy get the size's, not sure if you have noticed but the bells on the ksports are a bit grainy and don't have a very good finish.
chrisdicko - will see what I can find, I can confirm I can get ksport and performance friction size's easy enough
#13
Scooby Regular
iTrader: (2)
Join Date: Dec 2002
Location: All over the place, trying to stop putting the miles on!
Posts: 1,197
Likes: 0
Received 1 Like
on
1 Post
304*28mm AP Four Pots to fit under standard 16 inch wheels, i bought a new AP bell and it cost me a fourtune! at 35 quid plus vat each i would be interested in a spare set.
#16
My STI Type R is off road at the moment so I could send you my AP Brake Bell so you could take some measure-ments, as I would like a gold set of Brake Bells for my AP 355mm discs!!!
#29
As long as the bolt holes PCDs are right ( plus the offset etc) then any rotor can be fitted to a bell.
See my new set up for the P1 alcon brakes - I've had PF put on (by Zen) but AP were also available - they were just more expensive. So far very pleased with the PF
£35 + VAT is incredibly cheap for a bell
See my new set up for the P1 alcon brakes - I've had PF put on (by Zen) but AP were also available - they were just more expensive. So far very pleased with the PF
£35 + VAT is incredibly cheap for a bell