Hawkeye 06/07 AP Brake kits
#1
AP Brake kits
I've just started raising interest for AP brakes over on our RB320 club site but thought I'd extend it over here as the prices are very good.
About the product:
Calipers
All Performance Road Brake Calipers use conventional seals in conjunction with a dirt seal and are finished with a black PTFE based paint coating which is impervious to normal brake fluids & high brake temperatures, with the AP Racing logo highlighted in yellow, or gloss red with the logo highlighted in white.
Mounting Brackets
All brackets are individually designed for each application in either hard anodised aluminium or steel.
Mounting Bells
The bells are lightweight aluminium alloy, and hard anodised for durability. Each mounting bell is specifically designed for the application.
Brake Discs
The discs used in the AP Racing brake kits have been selected from our extensive race proven range which are synonymous with performance & quality throughout the racing world.
Sizes Ø285 (11.22") to Ø362mm (14.25") x 25.4mm (1.0") to 36mm (1.4") thick.
Brake Pads
Almost all AP Racing brake kits come complete with Ferodo DS2500 pads. These are ideally suited for all round performance road use. We can advise on, or specify and supply alternative pads specifically for track days.
Brake Hose
In most cases the appropriate Goodridge TUV approved steel braided hoses with nylon armour protection are supplied with each kit.
IMPORTANT NOTE - ROAD APPROVAL FOR BRAKE HOSES
In order to meet the requirements of the TUV, the FMVSS106, SVA and SAE 1401 standards for brake lines for road going vehicles, all fittings must be permanently attached to the hose.
RE-USABLE OR THREADED ATTACHED FITTINGS MAY NOT BE USED. ALL FITTINGS MUST BE CRIMPED OR SWAGED TO THE HOSE WHETHER THE HOSE IS RUBBER OR BRAIDED STEEL.
All Goodridge factory manufactured brake line kits are crimped and meet the requirements of the DOT and SAE. For full TUV approval, lines must pass a series of tests and be assembled in an approved assembly unit that meets all the requirements of the TUV office, including traceability. Consult the braided steel brake line experts 'Goodridge', if you are in any doubt on 01392 369090.
Fixings
Each kit contains a comprehensive installation guide and list of tightening torques. All mounting bolts & nuts are of high tensile steel and come with a sachet of Loctite 262. Shim washers are supplied in each kit to allow accurate positioning of the caliper on the brake disc, and allow for tolerance variations in different hubs/uprights.
Brake Fluid
All kits have 2 bottles of AP Racing Formula Dot 5.1 Brake & Clutch Fluid included.
The price shown below are for a setup on the MY06/07 Impreza STI but if you are interested, please add your name down on the list with your spec of car and the disc size, kit you want (i.e. front only, 330mm)
JUST TO ADD, AS I CANT AMEND THE TITLE - OPEN TO ALL MODELS OF IMPREZA's
AP Racing 6 pot caliper, 356mm disc (front) / 4 pot caliper ,335mm disc (rear) & braided hoses, Ferrodo DS2500 pads.
Individually these would cost - £2959.11 fitted (price INCLUDES VAT)
=============================================
for sets of 1 + 2's price would be £2670.53 fitted (price INCLUDES VAT)
=============================================
for 15 sets or more price would be £2336.66 fitted (price INCLUDES VAT)
=============================================
for just the fronts: £1549.83 (price INCLUDES VAT)
£70 less for supply only but cost/weight of postage will be approx £70
(fitting is @ Extreme Scoobies in Chelmsford)
NOTE: if you require other pads please specify which but be aware these would be additional costs.
================================================== ======
================================================== ======
Prices for the 330mm front kit setup:
330 AP kit these retail at £1683.40 plus vat (£1978)
If we get 10x 330mm kits or more then they can do these at £1430.89 plus vat (£1681.30)
Quote:
Question: I’ve got these wheels & so on, will they fit.
Answer: AP’s website has a great link at: Brake Kits, Brake Calipers, Brake Discs, Brake Fluid, Pads, Clutches from AP Racing
You can measure your own wheel sizes.
if you're interested, stick you name down below.
About the product:
Calipers
All Performance Road Brake Calipers use conventional seals in conjunction with a dirt seal and are finished with a black PTFE based paint coating which is impervious to normal brake fluids & high brake temperatures, with the AP Racing logo highlighted in yellow, or gloss red with the logo highlighted in white.
Mounting Brackets
All brackets are individually designed for each application in either hard anodised aluminium or steel.
Mounting Bells
The bells are lightweight aluminium alloy, and hard anodised for durability. Each mounting bell is specifically designed for the application.
Brake Discs
The discs used in the AP Racing brake kits have been selected from our extensive race proven range which are synonymous with performance & quality throughout the racing world.
Sizes Ø285 (11.22") to Ø362mm (14.25") x 25.4mm (1.0") to 36mm (1.4") thick.
Brake Pads
Almost all AP Racing brake kits come complete with Ferodo DS2500 pads. These are ideally suited for all round performance road use. We can advise on, or specify and supply alternative pads specifically for track days.
Brake Hose
In most cases the appropriate Goodridge TUV approved steel braided hoses with nylon armour protection are supplied with each kit.
IMPORTANT NOTE - ROAD APPROVAL FOR BRAKE HOSES
In order to meet the requirements of the TUV, the FMVSS106, SVA and SAE 1401 standards for brake lines for road going vehicles, all fittings must be permanently attached to the hose.
RE-USABLE OR THREADED ATTACHED FITTINGS MAY NOT BE USED. ALL FITTINGS MUST BE CRIMPED OR SWAGED TO THE HOSE WHETHER THE HOSE IS RUBBER OR BRAIDED STEEL.
All Goodridge factory manufactured brake line kits are crimped and meet the requirements of the DOT and SAE. For full TUV approval, lines must pass a series of tests and be assembled in an approved assembly unit that meets all the requirements of the TUV office, including traceability. Consult the braided steel brake line experts 'Goodridge', if you are in any doubt on 01392 369090.
Fixings
Each kit contains a comprehensive installation guide and list of tightening torques. All mounting bolts & nuts are of high tensile steel and come with a sachet of Loctite 262. Shim washers are supplied in each kit to allow accurate positioning of the caliper on the brake disc, and allow for tolerance variations in different hubs/uprights.
Brake Fluid
All kits have 2 bottles of AP Racing Formula Dot 5.1 Brake & Clutch Fluid included.
The price shown below are for a setup on the MY06/07 Impreza STI but if you are interested, please add your name down on the list with your spec of car and the disc size, kit you want (i.e. front only, 330mm)
JUST TO ADD, AS I CANT AMEND THE TITLE - OPEN TO ALL MODELS OF IMPREZA's
AP Racing 6 pot caliper, 356mm disc (front) / 4 pot caliper ,335mm disc (rear) & braided hoses, Ferrodo DS2500 pads.
Individually these would cost - £2959.11 fitted (price INCLUDES VAT)
=============================================
for sets of 1 + 2's price would be £2670.53 fitted (price INCLUDES VAT)
=============================================
for 15 sets or more price would be £2336.66 fitted (price INCLUDES VAT)
=============================================
for just the fronts: £1549.83 (price INCLUDES VAT)
£70 less for supply only but cost/weight of postage will be approx £70
(fitting is @ Extreme Scoobies in Chelmsford)
NOTE: if you require other pads please specify which but be aware these would be additional costs.
================================================== ======
================================================== ======
Prices for the 330mm front kit setup:
330 AP kit these retail at £1683.40 plus vat (£1978)
If we get 10x 330mm kits or more then they can do these at £1430.89 plus vat (£1681.30)
Quote:
Question: I’ve got these wheels & so on, will they fit.
Answer: AP’s website has a great link at: Brake Kits, Brake Calipers, Brake Discs, Brake Fluid, Pads, Clutches from AP Racing
You can measure your own wheel sizes.
if you're interested, stick you name down below.
Last edited by rb5 286; 25 April 2007 at 02:51 PM. Reason: amended to accomodate all versions of Subaru Models
Trending Topics
#8
Taken from the AP Website:
Almost all AP Racing Formula Big Brake upgrade kits come complete with Ferodo DS2500 pads. These are ideally suited for all round performance road use. We can advise on, or specify and supply alternative pads specifically for track days
Almost all AP Racing Formula Big Brake upgrade kits come complete with Ferodo DS2500 pads. These are ideally suited for all round performance road use. We can advise on, or specify and supply alternative pads specifically for track days
#12
Got an email from the supplier earlier
and prices for the 330mm front kit setup:
330 AP kit these retail at £1683.40 plus vat
If we get 10 330mm kits or more then we can do these at £1430.89 plus vat
Getting a few calls re I’ve got these wheels & so on, will they fit. I can’t say for all wheels though AP’s website has a great link at: Brake Kits, Brake Calipers, Brake Discs, Brake Fluid, Pads, Clutches from AP Racing
Then people can measure there own wheel sizes
Then people can measure there own wheel sizes
and prices for the 330mm front kit setup:
330 AP kit these retail at £1683.40 plus vat
If we get 10 330mm kits or more then we can do these at £1430.89 plus vat
#16
Here are two quick pics of my AP's. As you can see, both PCD's are catered for. Hope this helps mate.
Front 355mm disc, 6 pot caliper
Rear 335mm disc, 4 pot caliper
#18
Scooby Regular
iTrader: (7)
Join Date: Feb 2007
Location: Chichester, West Sussex
Posts: 1,178
Likes: 0
Received 2 Likes
on
2 Posts
AP bells come with both 5x100 PCD and 5x114.3 PCD holes drilled so these kits are not 'exclusively' for MY06 cars.
Here are two quick pics of my AP's. As you can see, both PCD's are catered for. Hope this helps mate.
Front 355mm disc, 6 pot caliper
Rear 335mm disc, 4 pot caliper
Here are two quick pics of my AP's. As you can see, both PCD's are catered for. Hope this helps mate.
Front 355mm disc, 6 pot caliper
Rear 335mm disc, 4 pot caliper
#21
#24
Scooby Regular
iTrader: (1)
Join Date: Oct 2004
Location: Half way up
Posts: 4,791
Likes: 0
Received 0 Likes
on
0 Posts
Some recon it's because the CP7040 6 pot is inferior whilst others say it's because Aston Martin use the same setup and therefore have payed for a lot of the development costs..
I'm getting some Ap 4 pots/330mm fitted (this week hopefully..) mainly as I want to keep the unsprung weight down to a minimum and apparently there ain't much difference..
I'm getting some Ap 4 pots/330mm fitted (this week hopefully..) mainly as I want to keep the unsprung weight down to a minimum and apparently there ain't much difference..
#28
Oh and for AP racing 6 pot 330mm pads give Circuit Supplies a call on 01525 385888.
£169.61 delivered for Pagid RS42 or £217.82 for Ferodo DS2500 (CP5070D51)
ASP Trading on 0191 4103770 also sell the Pagid pads for £110.63 + VAT
£169.61 delivered for Pagid RS42 or £217.82 for Ferodo DS2500 (CP5070D51)
ASP Trading on 0191 4103770 also sell the Pagid pads for £110.63 + VAT
Last edited by richto; 21 June 2007 at 04:03 PM.
Thread
Thread Starter
Forum
Replies
Last Post
shorty87
Full Cars Breaking For Spares
19
22 December 2015 11:59 AM
speedrick
Subaru Parts
0
26 September 2015 03:01 PM
MightyArsenal
Wheels, Tyres & Brakes
6
25 September 2015 08:31 PM