K sport pad alignment.
#1
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Oct 2009
Location: www.wy-scoobs.com
Posts: 1,298
Likes: 0
Received 0 Likes
on
0 Posts
K sport pad alignment.
Just fitted some new k sport 8 pots, 330mm. The pads sit about 4-5mm past the edge of the disc. It's as if the caliper mounting brackets are too big.
Anyone else had this issue?
Anyone else had this issue?
#4
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Oct 2009
Location: www.wy-scoobs.com
Posts: 1,298
Likes: 0
Received 0 Likes
on
0 Posts
I bought a set a couple of years ago and they were fine. The set I bought last week are Deffinatley not right, and another of my mates has the same issue.
Spoke to apex today who told me "that's just how they are", total dog **** if you ask me. Why would you design something to be perposley inefficient? Something has gone wrong in the manufacturing process.
Spoke to apex today who told me "that's just how they are", total dog **** if you ask me. Why would you design something to be perposley inefficient? Something has gone wrong in the manufacturing process.
#5
Scooby Regular
iTrader: (12)
Join Date: Aug 2010
Location: Northwest
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
Had same problem on the same kit few years ago, contacted apex and EBC about pad problem and EBC sent out a smaller pad to try but this didn't use the full disc. Used the larger ones in the end and the 3-4mm overhang just breaks off, don't worry about it.
#6
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Oct 2009
Location: www.wy-scoobs.com
Posts: 1,298
Likes: 0
Received 0 Likes
on
0 Posts
Thing is I do worrie about things like this. It's just poor development. The disc should be bigger or the caliper bracket should be smaller.
At least it's not something I've done wrong. Il check the caliper clearances and if all good il get the bracket machined to rectify the manufacturing defect.
At least it's not something I've done wrong. Il check the caliper clearances and if all good il get the bracket machined to rectify the manufacturing defect.
#7
Scooby Regular
iTrader: (1)
Join Date: Apr 2005
Location: In the Flatlands of Lincolnshire
Posts: 2,892
Likes: 0
Received 0 Likes
on
0 Posts
1. Are the disk's 330mm?
2. Could you have the calipers for the 356mm discs by mistake?
Over the weekend I will dig the K sport pads out for my 356mm kit and measure them and post the dimensions up.
2. Could you have the calipers for the 356mm discs by mistake?
Over the weekend I will dig the K sport pads out for my 356mm kit and measure them and post the dimensions up.
Trending Topics
#9
Did you find a solution for this, or did you just continue using them with misalignment and how did that turn out?
I'm installing them now and have the same issue, i strated a thread (with picture), now i just found yours.
my thread: https://www.scoobynet.com/wheels-tyr...s-too-big.html
I'm installing them now and have the same issue, i strated a thread (with picture), now i just found yours.
my thread: https://www.scoobynet.com/wheels-tyr...s-too-big.html
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM