Apexi AVC-R How??
09 December 2010, 08:09 PM
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Nov 2005
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
Apexi AVC-R How??
Hi Guy's
My new car has an Apexi AVC-R boost controller fitted and sitting on the dash.
But not knowing anything about them, i'm a little scared to touch it in case i mess anything up.
As it is all set-up.
All i'm looking to do is see how the 2nd stage of boost works.
How do i access this.
Are there any easy to follow steps.
Any help very much apprecicated.
Cheers Dave.
My new car has an Apexi AVC-R boost controller fitted and sitting on the dash.
But not knowing anything about them, i'm a little scared to touch it in case i mess anything up.
As it is all set-up.
All i'm looking to do is see how the 2nd stage of boost works.
How do i access this.
Are there any easy to follow steps.
Any help very much apprecicated.
Cheers Dave.
09 December 2010, 08:29 PM
#3
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Nov 2005
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
Er!!, yes mate, have looked at the manual and that's why i'm asking, very confusing, 
All i'm trying to do is find out how to set stage 1 and stage 2 boost
Basically after a dumbo's guide to setting stage 1 and stage 2 boost.
Cheers Dave.
All i'm trying to do is find out how to set stage 1 and stage 2 boost
Basically after a dumbo's guide to setting stage 1 and stage 2 boost.
Cheers Dave.
09 December 2010, 08:38 PM
#4
Former Sponsor
iTrader: (30)
Join Date: Jan 2005
Location: FB Tuning Workshop - HP27
Posts: 4,219
Likes: 0
Received 0 Likes
on
0 Posts
Has the AVCR already been properly configured by somebody who knows what they're doing with it?
What are you actually trying to do ? - Just change between the two preset boost levels, SettingA and SettingB?
What are you actually trying to do ? - Just change between the two preset boost levels, SettingA and SettingB?
09 December 2010, 08:54 PM
#6
Former Sponsor
iTrader: (30)
Join Date: Jan 2005
Location: FB Tuning Workshop - HP27
Posts: 4,219
Likes: 0
Received 0 Likes
on
0 Posts
turn on the ignition to power up the AVCR
Press PREV until you reach the main menu - MONITOR/SETTING/ETC
Highlight SETTING and push the right arrow - This will flick between SETTING A and SETTING B which are your 2 preset boost levels. Pressing the left arrow will turn the solenoid control off, and you will just be runnning at wastegate spring pressure
Whilst Setting A (or B) is highlighted, if you press NEXT, it will show you a sub menu for that boost setting. Select Number1 (Boost/Duty) and press NEXT again - this will show you the preset boost target, and if you press NEXT again, it will show you the solenoid duty cycle for the particular set boost target
Pushing PREV will take you back up the menu tree.
Read through the manual - Theres a lot of very useful features, and it's really easy to navigate (and set up) when you get the hang of it.
Press PREV until you reach the main menu - MONITOR/SETTING/ETC
Highlight SETTING and push the right arrow - This will flick between SETTING A and SETTING B which are your 2 preset boost levels. Pressing the left arrow will turn the solenoid control off, and you will just be runnning at wastegate spring pressure
Whilst Setting A (or B) is highlighted, if you press NEXT, it will show you a sub menu for that boost setting. Select Number1 (Boost/Duty) and press NEXT again - this will show you the preset boost target, and if you press NEXT again, it will show you the solenoid duty cycle for the particular set boost target
Pushing PREV will take you back up the menu tree.
Read through the manual - Theres a lot of very useful features, and it's really easy to navigate (and set up) when you get the hang of it.
Last edited by FB Tuning; 09 December 2010 at 08:59 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Mister:E
Subaru Parts
2
24 September 2015 01:37 PM