soes anyone know where i cant this pipe????

cant find it anywhere..

 

I have recently fitted the delete. I could not find the pipe either.

In the end i built my own. Cost around £45.

 

i have a freind who is selling one, pm your number and i'll pass it on to him

 

been looking for that one too - and no joy as yet!

 

Apexi - comes with the Power Intake.

 

thats the one my mate has if any of you are still looking for it

 

got mine from joz sounds brill

 

ok i like the apexi too, but hot air from under the bonnet??

 

You don't have to fit the filter.

It just works out a very expensive delete pipe.

 

ive an hks filter on mine and if i pop the bonnet after a thrash it is stone cold! seems to catch heaps of air coming through gap in bonnet.
Only time it's warm is when parked up and fan blows on it

 

I seriously hope you don't think I paid that much!

It was something like £40 from someone one here.

 

HKS filters aren't actually that good at filtering IIRC.

 

i made mine

probably cost 3 times as much as i couldnt find an apexi one at the time

but hey-ho

 

what do you mean? on the replacement element on it it has a higher micron rating thingy than k & n? im sure-ish

When i check the Maf etc it is always squeaky clean. Could I be letting crap into my engine? Hope not as I had a bottom end re-build in April past.

Good god im getting paranoid now, should i go for the RCM big boy?

 

I mean what I said. IIRC, they aren't actually that good at filtering. I wouldn't use one, and I don't know of anywhere that would recommend using one.

RCM used a K&N filter on the Gobstopper...............

 

I seriously hope i didn't too.

Induction cone or panel Peter??



First the exhaust and now your filter. Must be the weather.

Fwiw. K&N alllllll day long.

 

bump

 

Post #2 is your best bet. I got very lucky and found a second hand one forsale on here. The apexi wont create the correct angle if you plan on keeping the standard airbox

Mine


Theres a chance ill be selling it mine in a month or the beginning January as im going FMIC and Induction kit and gonna do a bit of a custom set up like in post #2

Send me a PM and ill let you know when i decide its coming off.

 

Why do you have half a can of Red Bull under the bulkhead??

 

It gives me wings!!!

Its wrapped around what i presume is the starter motor thing lol also got a motorhead wrist band on the brake fluid resovoir. Previous owner put them on and i havent removed them coz they look good

 

Wiper motor.

 

Glad i was close with "starter motor thing"

 

What will resonator delete pipe improve? induction sound?

 

It does give some extra induction noise. Also allows a less resticted flow of air, which 'in theory' should be colder/denser. I've not had chance to log it yet, but from what i have read and been advised, it should be ok.

I mainly did it for aesthetics.

 

Can someone tell me, what are the benefits to de-resonating the induction track??

I might do my car if there is advantages

 

anyone??

 

Better sound, as the resonator is in place to decrease induction noise. A straighter less interupted path for the air to flow through.

Its not gonna add an instant 10bhp or anything, but will maximize any potential gain with upgrades to the intake system.

if you can find or make one then definately do it, if only to maximize any future mods.

 

Thanks buddy, I think I will do something like b13bat has done

 

1x 80mm to 70mm elbow, 1x 70mm alloy joiner with 19mm take off and 1x 70mm to 60mm elbow. 4x clips and a sharp Stanley.

 

Thanks buddy, I will add that to my shopping list