Trying to fit FMIC, ABS?!.. Help needed..
#1
Scooby Regular
Thread Starter
Join Date: Jan 2007
Location: Northampton
Posts: 871
Likes: 0
Received 0 Likes
on
0 Posts
Trying to fit FMIC, ABS?!.. Help needed..
I've started fitting my FMIC today, but just as I am getting ready to cut my hole, I realise, I have ABS there....
Is it still possible to fit with ABS?
OR
Is this going to be one of them really annoying times where I have to put it all back together because the only way is removal of ABS?
Any help would be much appreciated.
Is it still possible to fit with ABS?
OR
Is this going to be one of them really annoying times where I have to put it all back together because the only way is removal of ABS?
Any help would be much appreciated.
#2
Scooby Regular
Thread Starter
Join Date: Jan 2007
Location: Northampton
Posts: 871
Likes: 0
Received 0 Likes
on
0 Posts
94 Turbo 2000, by the way
Is there a specific kit for cars with ABS and one for those without?
As I've never seen it advertised that way before, when advertised they just say 92-96 Impreza..
Is there a specific kit for cars with ABS and one for those without?
As I've never seen it advertised that way before, when advertised they just say 92-96 Impreza..
#5
Scooby Regular
Thread Starter
Join Date: Jan 2007
Location: Northampton
Posts: 871
Likes: 0
Received 0 Likes
on
0 Posts
Mines different to that, I had to remove heat shield from turbo, it goes over the top of the turbo and needs to go pretty much where the ABS is.
Think I'm just going to try to get it as close to the ABS as possible, as its the only way I can do it.
Think I'm just going to try to get it as close to the ABS as possible, as its the only way I can do it.
#6
Scooby Regular
Thread Starter
Join Date: Jan 2007
Location: Northampton
Posts: 871
Likes: 0
Received 0 Likes
on
0 Posts
I checked the pic out on your profile of your engine bay, it has the same ABS as mine, so I'm guessing it will fit, just doesnt look like it, Lol.
Thanks
#7
Scooby Regular
iTrader: (3)
I've started fitting my FMIC today, but just as I am getting ready to cut my hole, I realise, I have ABS there....
Is it still possible to fit with ABS?
OR
Is this going to be one of them really annoying times where I have to put it all back together because the only way is removal of ABS?
Any help would be much appreciated.
Is it still possible to fit with ABS?
OR
Is this going to be one of them really annoying times where I have to put it all back together because the only way is removal of ABS?
Any help would be much appreciated.
Trending Topics
#8
Scooby Regular
iTrader: (1)
Join Date: Jun 2009
Location: blackpool
Posts: 364
Likes: 0
Received 0 Likes
on
0 Posts
i had this problem last week mate what i did was unbolt the abs system then cut off one of the abs support arms the one tht bolts where the pipe needs to be.
then cyt the inner wing to desire and dress with rubber seal i used an old sunroof scrim
thn bolt the abs back in with the 2 bolts near the engoine and the one on the right as you look
as you have removed the left one
ps its easier to cut the abs support arm where it bends
hope this helps
then cyt the inner wing to desire and dress with rubber seal i used an old sunroof scrim
thn bolt the abs back in with the 2 bolts near the engoine and the one on the right as you look
as you have removed the left one
ps its easier to cut the abs support arm where it bends
hope this helps
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
33
29 August 2017 07:18 PM
JonMc
Subaru Parts
22
06 February 2016 09:50 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
20
22 October 2015 06:12 AM