Notices

ECU Codes and bad starting

Thread Tools
 
Search this Thread
 
Old 10 July 2007, 02:44 PM
  #1  
dash26
Scooby Newbie
Thread Starter
 
dash26's Avatar
 
Join Date: Jun 2002
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Default ECU Codes and bad starting

Hi all.

Please help with this irritating problem, whats happening is this. When I start the car from cold or hot, it wont start until i give it a little bit revs. It will then die on me if i take my foot off the revs. When i drive for a little way(say even 100ft), it will idle ok. But soon as i try and start it up again its got the same problem.

I have connected the under dash connections and watched the CEL, but its giving me a constant flash of about 1 sec intervals. Does anyone know what is going on here.

MYUK 94 wagon if its any more help

Thanks for any help.
Old 10 July 2007, 05:53 PM
  #2  
MY,k436suy
Scooby Regular
 
MY,k436suy's Avatar
 
Join Date: Feb 2007
Location: East Anglia, In a barn,where i was born.
Posts: 229
Likes: 0
Received 0 Likes on 0 Posts
Default

Coolant temperature sensor?
Old 11 July 2007, 11:43 AM
  #3  
dash26
Scooby Newbie
Thread Starter
 
dash26's Avatar
 
Join Date: Jun 2002
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by MY,k436suy
Coolant temperature sensor?
Thanks. But can you tell me where the coolant temp sensor is??
Old 11 July 2007, 12:39 PM
  #4  
myblackwrx
Scooby Regular
iTrader: (1)
 
myblackwrx's Avatar
 
Join Date: Mar 2006
Location: Dorset
Posts: 8,787
Likes: 0
Received 1 Like on 1 Post
Default

Looking at the engine bay it's to the top left of the lhs inlet manifold pipe and is a brown connector pligging into the block
Old 11 July 2007, 12:50 PM
  #5  
myblackwrx
Scooby Regular
iTrader: (1)
 
myblackwrx's Avatar
 
Join Date: Mar 2006
Location: Dorset
Posts: 8,787
Likes: 0
Received 1 Like on 1 Post
Default



In the gap below the recirc valve (round thing with the blue tubing) and the inlet manifold, you may need a torch to see it.
Old 11 July 2007, 04:03 PM
  #6  
dash26
Scooby Newbie
Thread Starter
 
dash26's Avatar
 
Join Date: Jun 2002
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Default

Great guys got it. Think this could be my fault as i took the blanking plates off the vents, thinking with it being summertime and all the heat. But with all the rain lately, maybe its sensor has got a bit damp. Do you think this could be the problem.

Thanks for the help anyway.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
38
17 July 2016 10:43 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
20
22 October 2015 06:12 AM
oilman
Trader Announcements
15
01 October 2015 11:55 AM
TECHNOPUG
General Technical
11
21 September 2015 05:42 PM
aaron_ions
General Technical
1
17 September 2015 10:42 AM



Quick Reply: ECU Codes and bad starting



All times are GMT +1. The time now is 03:20 PM.