Notices

APEXI AVC-R Help

Thread Tools
 
Search this Thread
 
Old 08 April 2006, 04:49 PM
  #1  
Harvez
Scooby Regular
Thread Starter
 
Harvez's Avatar
 
Join Date: Oct 2005
Posts: 140
Likes: 0
Received 0 Likes on 0 Posts
Default APEXI AVC-R Help

Hey just woundering all those who have the same boost controller ?

What boost and duty are you running on a stock engine (95 WRX), at the moment mine is running 0.70boost and 23% Duty , but it only ever boosts up to 0.70 after 100mph

And progressivly on the boost its all set to .7bar all the way through the revs

Whats the best boost and duty i should be using ?

Thanks for any info, or even betta progressive boost throu the revs, which should i be setting it to
Old 08 April 2006, 05:26 PM
  #2  
jaytc2003
Scooby Regular
iTrader: (1)
 
jaytc2003's Avatar
 
Join Date: Aug 2005
Location: Manchester ish
Posts: 18,547
Likes: 0
Received 0 Likes on 0 Posts
Default

would up your boost to 0.9 bar and definately increase the duty, it is way to low. Start with your duty at 50 and build up if needs be. IF you find you hit the fuel cut then reduce the duty slightly (a higher duty will give a bit of overboost so if your boost is set to 0.9 then you could get 1 bar on the overboost if you know what I mean). just have a play with different boost and duties jsut dont go silly
Old 08 April 2006, 05:33 PM
  #3  
Harvez
Scooby Regular
Thread Starter
 
Harvez's Avatar
 
Join Date: Oct 2005
Posts: 140
Likes: 0
Received 0 Likes on 0 Posts
Default

I'll try 0.9 but i was told to stay away from 1.0 on a stock engine, plus the fuel cut off is at a BAR isnt it ?

Also have you had a problem with the unit itself, mine wont remmeber A and B settings, so if i want to up the boost or lower i have to do it manually each time instead of having two pre-set settings
Old 08 April 2006, 05:40 PM
  #4  
jaytc2003
Scooby Regular
iTrader: (1)
 
jaytc2003's Avatar
 
Join Date: Aug 2005
Location: Manchester ish
Posts: 18,547
Likes: 0
Received 0 Likes on 0 Posts
Default

fuel cut is just over a bar. You can leave the boost at .7 and play with increasing the duty as doing this you can get over the .7 bar peak but it will or should then drop to hold the .7 bar

How have you wired you avcr up? When I first did mine it had power but wouldnt actually do anything. I ended up connecting the earth directly to the battery and problem was solved. (the scoobs apparently suffer from poor earths)
Old 08 April 2006, 06:06 PM
  #5  
Harvez
Scooby Regular
Thread Starter
 
Harvez's Avatar
 
Join Date: Oct 2005
Posts: 140
Likes: 0
Received 0 Likes on 0 Posts
Default

I cant remember now where i wired the earth to but ill strip it back tomorrow and find out, then maybe try earthing it in a different place and see it this solves the memory problem. I did phone APEXI up at one point and they said it was a common fult with some of the units and there isnt anythin that can be done about it which is nice to know since mines never worked properly
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
yabbadoo4
General Technical
10
24 September 2015 11:10 PM
Mister:E
Subaru Parts
2
24 September 2015 01:37 PM
johnnybon
Subaru Parts
5
23 September 2015 10:56 PM
Danowrx
General Technical
9
23 September 2015 02:48 PM
jason62
General Technical
13
21 September 2015 05:20 PM



Quick Reply: APEXI AVC-R Help



All times are GMT +1. The time now is 12:30 PM.