Check engine light
#1
Scooby Newbie
Thread Starter
Join Date: Nov 2005
Location: Shrewsbury
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Check engine light
Some advice please . Ive had the check engine light flicker on twice in the last two days and ive done the obvious and checked oil and water and no leaks . Also runs fine and could do with some help please .
#2
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
check the error codes.. this is how to reset and then check the error codes
ECU Reset and Error codes
Turn OFF the ignition
Connect Error code Connectors and Test Mode Connectors :
2 black connectors under dash, connect black to black and 2 green connectors under dash, connect green to green, they are by your left knee when sat in the drivers seat and often taped back to the loom if they haven't been used before.
Turn ON ignition but don't start the engine
Engine Check lamp comes on
Press accelerator pedal to the floor
Then return it to the half-throttle position and hold it there for two seconds
Release foot off the pedal completely
Start the engine
Check engine light error code is indicated by Pulsing lamp
If an error is detected then Check the ECU Code
If no error is detected - drive the car sensible for a couple of minutes
i.e. until warm (do not use boost or high rpm!)
When the ECU has been reset the Check Engine Light will flash
An Error Code is indicated by a flashing check engine light
of varying length of flash,
a flash of around once a second is the okay code and indicates all is well.
If an error code is detected Check the ECU Code
Turn ignition OFF and Disconnect Connectors
If there is a fault Check the Appropriate Sensor
Error Codes
An Error code is defined as a slow flash followed by fast flash
i.e 2 slow and 3 fast = 23 Mass Airflow sensor.
A continuous on/off at the same speed is no fault found.
Code Fault
11 Crankshaft position sensor
12 Starter switch
13 Camshaft position sensor
21 Engine coolant temperature sensor
22 Knock sensor
23 Mass air flow sensor
24 Idle air control solenoid
31 Throttle position sensor
32 Oxygen sensor
33 Vehicle speed sensor 2
35 Purge control solenoid valve
42 Idle switch
44 Wastegate control solenoid valve
45 Pressure sensor / Pressure exchange solenoid valve
51 Neutral position switch
ECU Reset and Error codes
Turn OFF the ignition
Connect Error code Connectors and Test Mode Connectors :
2 black connectors under dash, connect black to black and 2 green connectors under dash, connect green to green, they are by your left knee when sat in the drivers seat and often taped back to the loom if they haven't been used before.
Turn ON ignition but don't start the engine
Engine Check lamp comes on
Press accelerator pedal to the floor
Then return it to the half-throttle position and hold it there for two seconds
Release foot off the pedal completely
Start the engine
Check engine light error code is indicated by Pulsing lamp
If an error is detected then Check the ECU Code
If no error is detected - drive the car sensible for a couple of minutes
i.e. until warm (do not use boost or high rpm!)
When the ECU has been reset the Check Engine Light will flash
An Error Code is indicated by a flashing check engine light
of varying length of flash,
a flash of around once a second is the okay code and indicates all is well.
If an error code is detected Check the ECU Code
Turn ignition OFF and Disconnect Connectors
If there is a fault Check the Appropriate Sensor
Error Codes
An Error code is defined as a slow flash followed by fast flash
i.e 2 slow and 3 fast = 23 Mass Airflow sensor.
A continuous on/off at the same speed is no fault found.
Code Fault
11 Crankshaft position sensor
12 Starter switch
13 Camshaft position sensor
21 Engine coolant temperature sensor
22 Knock sensor
23 Mass air flow sensor
24 Idle air control solenoid
31 Throttle position sensor
32 Oxygen sensor
33 Vehicle speed sensor 2
35 Purge control solenoid valve
42 Idle switch
44 Wastegate control solenoid valve
45 Pressure sensor / Pressure exchange solenoid valve
51 Neutral position switch
#3
Scooby Newbie
Thread Starter
Join Date: Nov 2005
Location: Shrewsbury
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Thanks very much Mr monster . Very well written , managed to follow it well. The test found no faults so my mind is at ease now . Cheers mate , adcar .
#4
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
If the error code occurs again.. connect just the black plugs to read the code without resetting the ecu.. but it is obviously not a major all the time problem, or might have been just a one off.
Simon
Simon
Thread
Thread Starter
Forum
Replies
Last Post
charlesr
General Technical
9
28 September 2015 09:16 AM
TylerD529
Lighting and Other Electrical
5
20 September 2015 12:10 PM