Front number plate nut has sheared,What do I do??
#1
Scooby Regular
Thread Starter
Join Date: Oct 2001
Location: 1 of the ESC 1
Posts: 1,997
Likes: 0
Received 0 Likes
on
0 Posts
Hopefully I can describe my problem:
Whilst putting a new plate on the Scoob (Terzo), one of the the screws snap in the nuts on the small grill thats below the front bumper and above the front front spoiler. I tried to remove the remaining thread, but ended up pushing the thread and retaining nut inside the support. I have had a good look how to remove the whole assembly, to see if it can be repaired or replaced but I can't see how it comes off.
To save hassle I stuck the new plates on with Halfords adhesive spacer pads, but after a bit of (ahem) press-on driving I discovered the plate was just about holding on, therefore I removed the plate.
Does anyone know how to fix this problem. Or does it mean I have to jack the car up, remove the grill (somehow) and replace it??
Your comments will be gratefully received,
Ed
Whilst putting a new plate on the Scoob (Terzo), one of the the screws snap in the nuts on the small grill thats below the front bumper and above the front front spoiler. I tried to remove the remaining thread, but ended up pushing the thread and retaining nut inside the support. I have had a good look how to remove the whole assembly, to see if it can be repaired or replaced but I can't see how it comes off.
To save hassle I stuck the new plates on with Halfords adhesive spacer pads, but after a bit of (ahem) press-on driving I discovered the plate was just about holding on, therefore I removed the plate.
Does anyone know how to fix this problem. Or does it mean I have to jack the car up, remove the grill (somehow) and replace it??
Your comments will be gratefully received,
Ed
#2
My plates ae held on with the Halfords double sided stickers and have been on for at least 6 months.
Try again but this time heat up the back of the plate and the bumper with a hot air gun or hair dryer before fixing it. Once it's warm and dry clean it with brake cleaner or some other serious cleaner / degreaser and keep warming it. Once all the solvents gone stick the plate on and hold it somehow, lean something against it or tape it in place with tank tape or similar for a couple of hours.
Try again but this time heat up the back of the plate and the bumper with a hot air gun or hair dryer before fixing it. Once it's warm and dry clean it with brake cleaner or some other serious cleaner / degreaser and keep warming it. Once all the solvents gone stick the plate on and hold it somehow, lean something against it or tape it in place with tank tape or similar for a couple of hours.
#3
My screw was plastic.....I drilled it out with as large a drill I could use without damaging the captive thread. Then pushed the swarf out with a stick!
Then inserted new bolt - worked a treat.
BT
Then inserted new bolt - worked a treat.
BT
#4
Drag it!
iTrader: (1)
Join Date: Jun 2002
Location: Flame grilled Wagon anyone?
Posts: 9,866
Likes: 0
Received 0 Likes
on
0 Posts
Done this on all 3 scoobs i have had.
Easiest way is to kncok the backing plate off comepletely, thats what the nut is attached to, just push on the other side and it should pop off.
Then once you have done that, get some self tapping screws with plastic cap covers to match the position on your plate, mount the plate 1cm highere ow lower, and self tap into the plastic backing.
Hope that makes sense.
Steven
Easiest way is to kncok the backing plate off comepletely, thats what the nut is attached to, just push on the other side and it should pop off.
Then once you have done that, get some self tapping screws with plastic cap covers to match the position on your plate, mount the plate 1cm highere ow lower, and self tap into the plastic backing.
Hope that makes sense.
Steven
#5
Scooby Regular
Thread Starter
Join Date: Oct 2001
Location: 1 of the ESC 1
Posts: 1,997
Likes: 0
Received 0 Likes
on
0 Posts
Sorry to bring the subject back up again. Today I spent the best part of half an hour trying to work out how the supports unclip. Am I becoming a serious feckwit as I cannot work how it comes off and I'm certainly not going to try to force it off.
Please help before I go absolutly mental,
Cheers,
Ed
Please help before I go absolutly mental,
Cheers,
Ed
#6
Track Day Organiser
Ed
I did the same thing with my Previous car
I just used the halford tape heated up as suggested above
When that failed I just bought a new car
Just kidding
Phil
I did the same thing with my Previous car
I just used the halford tape heated up as suggested above
When that failed I just bought a new car
Just kidding
Phil
Thread
Thread Starter
Forum
Replies
Last Post
shorty87
Full Cars Breaking For Spares
19
22 December 2015 11:59 AM
shorty87
Wheels And Tyres For Sale
0
25 September 2015 08:36 PM
MightyArsenal
Wheels, Tyres & Brakes
6
25 September 2015 08:31 PM