Who to go to for map north west? - ScoobyNet.com - Subaru Enthusiast Forum



Engine Management and ECU Remapping This section is to discuss the various aspects of engine management modification for your Subaru.

Who to go to for map north west?

Reply
 
 
 
Thread Tools Search this Thread
Old 16 February 2018, 10:08 PM   #1  
SubaruHatchSTI
Scooby Newbie
Thread Starter
 
Join Date: Jan 2018
Location: Manchester England
Posts: 19
Default Who to go to for map north west?

Sorted an exhaust for the sti hatch next mission is to get it booked in for a decent map, not bothered about figures or gaining loads of bhp more just a map to help reliability. I know a lot of the big ones may be booked up for a bit so want to get it booked in. Donít mind travelling just not too far. Who do you guys reccomend and any I should stay away from? Thank you
SubaruHatchSTI is offline   Reply With Quote
Old 16 February 2018, 10:49 PM   #2  
bighead
Scooby Regular
iTrader: (1)
 
bighead's Avatar
 
Join Date: Jun 2002
Posts: 3,974
Default

try Steve Cotton at Cotton.com near Preston
bighead is offline   Reply With Quote
Old 16 February 2018, 10:56 PM   #3  
si_pow
Scooby Newbie
 
Join Date: Oct 2016
Location: NW England
Posts: 13
Default

Im in the same situation mate. Been trying to get hold of andy forrest but no reply but both cams performance and as performance can do it cheaper and are a bit closer. Not sure who to go with myself
si_pow is offline   Reply With Quote
Old 17 February 2018, 03:39 AM   #4  
ZANY
Scooby Regular
 
Join Date: Oct 2014
Location: ....
Posts: 4,838
Default

I also recommend Anthony through Brian at cams performance

The only mapper who I can trust to do a good job and who I would allow to work/tune my jdm impreza,reachable even if busy , takes the time to explain if need be,
Down to earth top man

Also has his own premises of business
ZANY is offline   Reply With Quote
Old 17 February 2018, 01:50 PM   #5  
SubaruHatchSTI
Scooby Newbie
Thread Starter
 
Join Date: Jan 2018
Location: Manchester England
Posts: 19
Default

Thanks for advice people going to give cams a call Monday morning��
SubaruHatchSTI is offline   Reply With Quote
Old 17 February 2018, 01:50 PM   #6  
SubaruHatchSTI
Scooby Newbie
Thread Starter
 
Join Date: Jan 2018
Location: Manchester England
Posts: 19
Default

Or if not Steve cotton one of the two��
SubaruHatchSTI is offline   Reply With Quote
Old 17 February 2018, 07:05 PM   #7  
edger-360
Scooby Regular
 
Join Date: May 2007
Location: west mids
Posts: 57
Default

Andrew Carr is good on hatch ecus,try TEG or Poleposition as they him on a regular basis
edger-360 is offline   Reply With Quote
Old 27 April 2018, 07:42 PM   #8  
darrenk1987
Scooby Newbie
 
Join Date: Apr 2018
Location: Manchester
Posts: 20
Default

Quote:
Originally Posted by SubaruHatchSTI View Post
Thanks for advice people going to give cams a call Monday morning��
where did you end up getting it mapped? looking to possibly get mine done at cams by ade tuning..
darrenk1987 is offline   Reply With Quote
Old 12 June 2018, 09:37 PM   #9  
si_pow
Scooby Newbie
 
Join Date: Oct 2016
Location: NW England
Posts: 13
Default

Quote:
Originally Posted by darrenk1987 View Post
where did you end up getting it mapped? looking to possibly get mine done at cams by ade tuning..
i got mine remapped by ADE through cams. Had the air pump removed for catch cabs, the vf48 installed, 3" downpipe to suit rest of system, walbro 255, and the 3 pot fitted at same time. Labour was really reasonable and the guys at cams were really helpful.

On the way home though it started to overboost and then **** itself cruising down he motorway in 5th at 80mph and black smoke poured out the back of it and had oil blowing out of oil cap, and all the breather hoses were drenched in oil. Now its rebuild time. Was only a matter of time from what i hear with these **** pistons so not blaming ADE
si_pow is offline   Reply With Quote
Old 13 June 2018, 04:39 AM   #10  
ZANY
Scooby Regular
 
Join Date: Oct 2014
Location: ....
Posts: 4,838
Default

Quote:
Originally Posted by si_pow View Post
i got mine remapped by ADE through cams. Had the air pump removed for catch cabs, the vf48 installed, 3" downpipe to suit rest of system, walbro 255, and the 3 pot fitted at same time. Labour was really reasonable and the guys at cams were really helpful.

On the way home though it started to overboost and then **** itself cruising down he motorway in 5th at 80mph and black smoke poured out the back of it and had oil blowing out of oil cap, and all the breather hoses were drenched in oil. Now its rebuild time. Was only a matter of time from what i hear with these **** pistons so not blaming ADE
Very sorry to hear hope you get it sorted without too much hassle
ZANY is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
best place/price for ECUTEK re map in north west? rs250gpracer General Technical 8 03 February 2008 01:40 AM
Garages in the North and North West Gav-WRX Northern (England) 14 25 February 2006 12:02 AM
The Official North Wales / North West NOB meet thread Steve001 Wales 4 06 June 2004 05:24 PM
North Wales/North West Crew (& everyone else :-)) Steve001 Wales 9 08 January 2004 02:23 PM
Wheel painting in North East or North West Up_North Wheels, Tyres & Brakes 7 14 August 2002 10:07 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT +1. The time now is 02:19 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.