what model is this rear diff for? (pics inside)
20 January 2008, 12:30 PM
#2
It is a 4:444 diff ratio (40 / 9)
I am sure it is not a Subaru Diff. The open and viscous Subary diffs are not welded together like that.
The only person i know with in-depth knowledge is David at Welcome to the API website.
Try sending him the pics to his email.
I am sure it is not a Subaru Diff. The open and viscous Subary diffs are not welded together like that.
The only person i know with in-depth knowledge is David at Welcome to the API website.
Try sending him the pics to his email.
20 January 2008, 12:56 PM
#4
Scooby Regular
Thread Starter
Join Date: Apr 2005
Location: in deep from behind
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
cheers for your replys 911 & moz, it definatly came out of a subaru casing (i took it out) hopefully david will pop along if not i will mail him.
anyone else?
anyone else?
20 January 2008, 05:45 PM
#5
Moz:
Out of interest, what model? I have an Sti Viscous sitting on my garage floor and it is nothing like that. Also I have a plated Sti rear also nothing like that, so curious!
Out of interest, what model? I have an Sti Viscous sitting on my garage floor and it is nothing like that. Also I have a plated Sti rear also nothing like that, so curious!
20 January 2008, 09:36 PM
#6
Former Sponsor
iTrader: (4)
Join Date: Jul 2003
Location: @Junc 12, M40 Warwicksh; 01926 614522 CV33 9PL -Use 9GX for Satnav. South Mids Alcatek ECu dealer
Posts: 6,377
Likes: 0
Received 3 Likes
on
3 Posts
Even so, you cannot buy bits for them, even if you do grind the welds off to get it to bits. The main case cracks under the pressure generated inside and once cracked, it is a bin job.
David APi
20 January 2008, 10:05 PM
#7
Scooby Regular
Thread Starter
Join Date: Apr 2005
Location: in deep from behind
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
thanx for clearing that up david,that diff as far as i know is ok, i have put new bearings in my diff(uk) but i broke the cap the bearings run round in(where the drive shaft goes in) so i paid for this diff just for that one piece, so this diff is not needed. i was just curious though this diff is nothing like my uk one.
Trending Topics
21 January 2008, 01:27 PM
#8
Scooby Regular
iTrader: (1)
Join Date: Feb 2006
Location: Warwickshire, UK
Posts: 2,099
Likes: 0
Received 0 Likes
on
0 Posts
Agree with david, I think its the Suretrac out of the P1 and some bugeyes the giveaway is the oil scoops, they are a nice road diff (better than a VC) but no good for motorsport! I'm sure you could sell it readily enough!
Simon
Simon
Last edited by The rookie; 21 January 2008 at 01:30 PM.
21 January 2008, 08:58 PM
#9
Scooby Regular
Thread Starter
Join Date: Apr 2005
Location: in deep from behind
Posts: 636
Likes: 0
Received 0 Likes
on
0 Posts
cheers for your reply rookie, if someone wanted it i would sell it, i have no need for it i have all the casing apart from the one end piece. ill see, it might pop up on fleabay. lol
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM
Scott@ScoobySpares
Full Cars Breaking For Spares
7
14 December 2015 08:16 AM
Mattybr5@MB Developments
Full Cars Breaking For Spares
20
22 October 2015 06:12 AM
