not enough power?
#1
on my95 wrx -i now have fitted a boost guage and car is only running on 0.5 bar, this is not correct? can anyone tell me why, or how to up the boost pressure ? please.
#2
No you are correct this is not the full boost pressure. That figure is around what the ECU limits to when there is a problem with a sensor, for saftey of the engine.
Try searching on here for CEL codes and ECU resets, it may help point you in the right direction, if this is the problem.
Gary
Try searching on here for CEL codes and ECU resets, it may help point you in the right direction, if this is the problem.
Gary
#5
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
Had the car been modified before you purchased it? Check to make sure the pipe from the turbo outlet nipple goes to the 3 port solenoid valve(solenoid valve is in front of the drivers side suspension turret behind airbox) then from the solenoid to the actuator on the turbo. The other pipe should go back to the bottom of the black intake chamber.
#6
have checked yhat and the botom pipe on the soliniod is blocked off with a bolt and goes nowhere, what next it has stumped me. i suppose it is time to take to a specalist?
#7
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
So the bottom pipe (bleed) is blocked off which normally goes to the resonator box? The other 2 pipes are connected to the turbo nipple and other to actuator on wastegate? If this is the case you are bleeding into a 'dead' end therefore the actuator will open at its nominal spring pressure. I take it you are not using an aftermarket boost controller ie Blitz HKS Dawes etc? If you are using standard boost control ie 3port solenoid this bottom pipe from solenoid needs un-blanking and venting preferably back into the iduction tract but this isn't absolutely necessary.
Hope this helps
Hope this helps
Trending Topics
#9
i have unblocked the boost contoller bottom pipe where the bolt was and connected it to the induction system where it waso blocked with a screw- car is now running on top form,1.6 on the gauge. i think it is high now as i turned the bar on the actuator.i shall turn this bak now. thanks for the help.cheers
#10
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
Is that 1.6bar? Cos that is very high, you should be running approx 0.9bar (12.7psig) standard. Try adjusting the actuator arm back to its original position. Has the car been running lowish boost since you purchased it cos I looks like it may have been frigged to cover up a problem. Is the car standard?
#12
Scooby Regular
Join Date: Apr 2003
Location: Cambridgeshire
Posts: 1,541
Likes: 0
Received 0 Likes
on
0 Posts
What modifications are you running? 1.4Bar without any mods is way too high and possibly why the crank let go previously. If you are running with standard Intercooler, Injectors etc personally I wouldn't run no more than 15-16psig(1-1.1bar)which is about the limit for a std map sensor. This also leads me to thinking either you are not running a std ECU or someone has fitted a fuel cut defencer(Enables fuel cut to be raised)as a std ECU cuts way below 1.4bar. Do you have a knocklink or Lambdalink fitted as I suspect the engine will be severely detonating with the current boost.
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM