URGENT wiring/loom help needed (simple question really)
#1
Right, still going through my conversion and i have now managed to match up the WRX loom perfectly missing of the non required sensors.
BUT.... there are three connectors hanging around above the gearbox. I am assuming one is the knock sensor (the single wire).
what are the other two???
also, anyone got a wiring diagram for the STi £ throttle bodie to a WRX loom (3 wires on STi, 4 on WRX)
BUT.... there are three connectors hanging around above the gearbox. I am assuming one is the knock sensor (the single wire).
what are the other two???
also, anyone got a wiring diagram for the STi £ throttle bodie to a WRX loom (3 wires on STi, 4 on WRX)
#2
Scooby Regular
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
bit more info would help.. however.. 92 -96 so other years are similar..
Around the top of the gearbox should be..
Water Temp
Fan Switch
TPS
ISCV
Knock Sensor
Ground From to Inlet manifold.
Ground direct to bracket on Starter
12v feed to solenoid / starter
Solenoid Trigger / Start Wire
Then to the left of the gearbox on pre 98 is Lambda, VSS, Reverse Sw., Neutral Sw.
Im sure Ive missed some.. ooh I have gnd.. & starter..
Around the top of the gearbox should be..
Water Temp
Fan Switch
TPS
ISCV
Knock Sensor
Ground From to Inlet manifold.
Ground direct to bracket on Starter
12v feed to solenoid / starter
Solenoid Trigger / Start Wire
Then to the left of the gearbox on pre 98 is Lambda, VSS, Reverse Sw., Neutral Sw.
Im sure Ive missed some.. ooh I have gnd.. & starter..
#3
Hi Jon, on my93 wrx there are three connectors coming from the wiring loom atached (ive spelt that wrong?) to the bulkhead, the single wire is the knock sensor the other 2 are cam sensor and crank sensor. hopr thats somer use KARL p.s there is also another single wire connector in the same area but this is the power steering warning light and this will connect to the knock sensor as well, which is great fun when you go round corners ):
#6
Scooby Regular
iTrader: (1)
Join Date: Mar 2002
Location: Norn Iron
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
Id guess the connectors he refers to are for the knock sensor ( one wire ), cam sensor, and crank sensor.
These are the only 3 sets of connectors that are not actually part of the the engine wiring loom as such.
The main loom runs through the inlet manifold, and feeds varoius items such as the TPS, ISCV injectors etc etc, and is cable tied to the manifold, with 2 main multiplugs beside the battery on most cars. ( some models do vary though )
These are the only 3 sets of connectors that are not actually part of the the engine wiring loom as such.
The main loom runs through the inlet manifold, and feeds varoius items such as the TPS, ISCV injectors etc etc, and is cable tied to the manifold, with 2 main multiplugs beside the battery on most cars. ( some models do vary though )
Thread
Thread Starter
Forum
Replies
Last Post
MeisterR
Car Parts For Sale
1
15 September 2015 07:07 PM
robbie1988
Wanted
2
13 September 2015 09:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 06:51 PM