frayz

iTrader: (7)

Yeah that's what I mean mate. My car does sod all mileage too. But the one or two polished items I have are a pain in the ****.

Looks lovely mate, good luck.

martin850

iTrader: (51)

Nice progress Ryan

mickywrx

iTrader: (29)

prodriverules

iTrader: (52)

I know what you mean frayz and I had figured as much,guess I'll be getting the autosol out more than I'd hoped lol

Thanks for the comments though guys.

prodriverules

iTrader: (52)

Got the motor all cleaned up and applied a bit of VHT paint to freshen it up,also removed the front covers ready for cleaning/painting after I decide what colour to do them.
I also need to remove the rocker covers to clean/paint them too but again once I decide what colour,thinking maybe crinkle red but not 100% sure

Removed the water pipes to give them a sand down and repaint and got them back on the motor,I can't really do a lot more as I now need to get my sensors off TimH in preparation for the toucan install,it's a lot easier to get the oil pressure/temp sensors in while there is no ancillaries in the way!

JTinnovations

iTrader: (2)

Looking *really* good Ryan

Sensor here ready to send as soon as you want them...have EGT's here now but waiting on compression glands to come in

prodriverules

iTrader: (52)

Thanks Tim,if you send the oil pressure and temp with adators one's on down that would be great as I can crack on with putting the motor back together,the other one's won't be needed for a while lol and I can put them on when needed

JTinnovations

iTrader: (2)

Even better - I'll drop them in to you on Tuesday...spending tomorrow night near Hay-on-Wye and then driving to Coventry on Tuesday and passing your door

prodriverules

iTrader: (52)

Oh and I also need to remove and paint that lower water pipe coming from the modine which I clearly forgot and have just seen on the picture

prodriverules

iTrader: (52)

Well there's a stroke of luck!
Look forward to it Tim,will you be in the black beauty?

JTinnovations

iTrader: (2)

Nope, will be in the "white wonder"

prodriverules

iTrader: (52)

I can take a look at that bumper with my own eye's then and see what I make of it!

JTinnovations

iTrader: (2)

Excellent...bumper will need some of your tlc in due course as it had a useless "smart repair" at some point and it's peeling. But would be good to get your opinion on the rear bumper colour matching etc

prodriverules

iTrader: (52)

No worries I'll see you on Tuesday Tim

JTinnovations

iTrader: (2)

FYI - going to Coventry to collect these for the black beauty

prodriverules

iTrader: (52)

Me like a LOT!!
Look like there in A1 condition as well Tim.

JTinnovations

iTrader: (2)

Hope so Ryan, otherwise will be a wasted journey!!

prodriverules

iTrader: (52)

Well your heading in the right direction if they need a prodrive makover
Could be a bargaining chip if they have any damage as well

JonMc

iTrader: (51)

About time you got off your **** and did something, looking very tidy - could almost be tempted to do mine

prodriverules

iTrader: (52)

Got the rocker covers removed and painted in matt black to keep with the silver black theme along with painting the cambelt covers in crinkle red.
Also got the crossover pipe installed and carl davey reverse alternator lower bracket on








TimH is dropping by tomorrow to drop in the adaptors/sensors for oil pressure and temperature so I will be able to install them and then get the manifold etc back on.

prodriverules

iTrader: (52)

As I have made the decision to delete the ABS I was contemplating how to go about the conversion as I need to incorporate a bias valve when I stumbled upon this lovely little setup!

JonMc

iTrader: (51)

Looking very tidy Ryan - I know I have one rocker cover gasket to sort when I swap the turbo and with everything else coming off the top half of my engine may start looking that good - need to sort my cam belt covers though as a couple of the captive nuts have escaped

Keep it going and you'll have it finished by Christmas (2020).

You bringing the foggy to the Prodrive gathering then

prodriverules

iTrader: (52)

Yeah 2020 isn't to far off I reckon
It will be nice to have it all looking so good though and if your going to do it then do it right!

Certainly not a good thing to have captive nuts floating about

Dirk Diggler 75

Lookin good.lovin the crinkle red ..........

JonMc

iTrader: (51)

Nice set-up, I'm planning to sort all mine on Saturday - would have been this weekend but I'm in Liverpool for a family thing. Should have the calipers sorted and the bias valve mounted under the bonnet to allow for tweaking but not whilst driving

Cannon Fodder

iTrader: (100)

Yes good idea to delete the ABS, I wonder where that came from...

Good progress as well Ryan, it's nice to see you have been a very busy boy this weekend.

prodriverules

iTrader: (52)

I'm probably going to mount my bias valve in the car Jon so I can easily adjust it while driving.

Yes Ty I'll grant you this one my good friend
It's a one time thing though

JonMc

iTrader: (51)

I'm looking to remote the controls from my PSI3 to the steering wheel so I'll have enough toys to play with in the car. Need to get some pics up too as I've splashed a litre of plasti-dip around the interior with plenty more planned

prodriverules

iTrader: (52)

Sounds like a really nice touch that Jon,it would be good to see the pics of the interior mate!!

JonMc

iTrader: (51)

I'll sort some when I get home, the trip was a little unexpected.