08/09 Hatches, Stand up and show yourselves!!!
Scooby Regular
I wouldn't buy a sc46 after seeing the welds on the exhaust housing blow twice on two different turbos
I ended up going for a forced performance red from the states (brought second hand off here) I had to buy there inlet and oil fitting kit aswell as the turbo inlet is 84mm but it's only around 1300 dollars for the turbo inlet and fitting kit so around 850 in sterling for the lot , so prob around £1000 once it's into the UK with dutys
I'm at 420 @1.1 bar but maxed my injectors
Scooby Senior
Scooby Senior
Do you need a re map once its fitted?
Scooby Regular
Hi domino,
Thanks for the info and and kind advice. Never heard of them before. Just been in their website and unless I could find a second hand one, they will end up being more expensive than the sc46. Think I may go for the sc42, apparently it's the best inbetweener with great spool up times. Any recommendations on good value injectors?? I was advised 1000cc off Scoobyclinic for wanting 450bhp but I feels that's too much, would the spray pattern suffice having 1000cc on 400ish bhp, I thought 750's would do?
Thanks for the info and and kind advice. Never heard of them before. Just been in their website and unless I could find a second hand one, they will end up being more expensive than the sc46. Think I may go for the sc42, apparently it's the best inbetweener with great spool up times. Any recommendations on good value injectors?? I was advised 1000cc off Scoobyclinic for wanting 450bhp but I feels that's too much, would the spray pattern suffice having 1000cc on 400ish bhp, I thought 750's would do?
I wouldn't buy a sc46 after seeing the welds on the exhaust housing blow twice on two different turbos
I ended up going for a forced performance red from the states (brought second hand off here) I had to buy there inlet and oil fitting kit aswell as the turbo inlet is 84mm but it's only around 1300 dollars for the turbo inlet and fitting kit so around 850 in sterling for the lot , so prob around £1000 once it's into the UK with dutys
I'm at 420 @1.1 bar but maxed my injectors
I ended up going for a forced performance red from the states (brought second hand off here) I had to buy there inlet and oil fitting kit aswell as the turbo inlet is 84mm but it's only around 1300 dollars for the turbo inlet and fitting kit so around 850 in sterling for the lot , so prob around £1000 once it's into the UK with dutys
I'm at 420 @1.1 bar but maxed my injectors
Scooby Senior
Have a proper talk with Kev at SC and see what they advise with the build theyve done.
If they do it for you there's no one else to confuse the situation any more
;-)
If they do it for you there's no one else to confuse the situation any more
;-)
Scooby Regular
iTrader: (5)
Scooby Regular
Scooby Regular
iTrader: (1)
Join Date: Mar 2015
Location: Nottingham
Posts: 185
Likes: 0
Received 0 Likes
on
0 Posts
Scooby Senior
Scooby Regular
Join Date: Nov 2008
Location: Worcestershire
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Hydro dipped carbon, couldn't get the quality expected from genuine carbon parts So had my original part dipped. Done a brilliant job, as wanted to mimic roof wrap.
Hydro dipped Carbon
Hydro dipped Carbon
Scooby Regular
iTrader: (5)
immense to drive, bit hairy in the wet giving it beans from a stand still
Scooby Regular
Hi domino,
Thanks for the info and and kind advice. Never heard of them before. Just been in their website and unless I could find a second hand one, they will end up being more expensive than the sc46. Think I may go for the sc42, apparently it's the best inbetweener with great spool up times. Any recommendations on good value injectors?? I was advised 1000cc off Scoobyclinic for wanting 450bhp but I feels that's too much, would the spray pattern suffice having 1000cc on 400ish bhp, I thought 750's would do?
Thanks for the info and and kind advice. Never heard of them before. Just been in their website and unless I could find a second hand one, they will end up being more expensive than the sc46. Think I may go for the sc42, apparently it's the best inbetweener with great spool up times. Any recommendations on good value injectors?? I was advised 1000cc off Scoobyclinic for wanting 450bhp but I feels that's too much, would the spray pattern suffice having 1000cc on 400ish bhp, I thought 750's would do?
Iv hit 420 on standard 565s and maxed them out , im swapping to 800cc and been told that's fine for the 500+ I'm after so 750 would be fine imo
Scooby Regular
iTrader: (5)
I ran 750cc denso injectors in my hatch.
Scooby Senior
Jase doing it then
Scooby Regular
Got loads of parts always laying around so I'm just using some sard ones that iv had spare but I'm told there good ones and spray well so should do the job just fine , Perrin rails , SX FPR ,sytec external pump and under bonnet swirl pot should sort my fuel shortage out for a while
Scooby Senior
no, i've not had mine done.
I'm quite happy how it is.
I'm quite happy how it is.
Scooby Regular
iTrader: (4)
Got my kit now thanks NT11. Fitting it next Sunday along with a Prodrive decat pipe and having it mapped by Duncan on the Thursday.
Will post up results afterwards.
Will post up results afterwards.
Scooby Senior
without...
with...
After doing 120miles today
I must say the car feels so much more planted on the front end and feels like it's in place on every bend, island and camber.
Well worth the expense to have a real STi part
with...
After doing 120miles today
I must say the car feels so much more planted on the front end and feels like it's in place on every bend, island and camber.
Well worth the expense to have a real STi part
What spark plugs are you guys using and any recommendations please? I will be servicing the car shortly and want to make sure everything is tip top before fitting a full 3" Miltek and mishimoto CAIK and Bob Rawle will be tweaking my map. Current spec is fully forged 330S with billet Owens 20g turbo. Thanks
[QUOTE
After doing 120miles today
I must say the car feels so much more planted on the front end and feels like it's in place on every bend, island and camber.
Well worth the expense to have a real STi part [/QUOTE]
If you haven't already done it I can highly recommend upgrading the rear ARB, steering rack bushes and anti lift kit also. The handling on mine is transformed!
After doing 120miles today
I must say the car feels so much more planted on the front end and feels like it's in place on every bend, island and camber.
Well worth the expense to have a real STi part [/QUOTE]
If you haven't already done it I can highly recommend upgrading the rear ARB, steering rack bushes and anti lift kit also. The handling on mine is transformed!
Scooby Regular
iTrader: (4)
Fitted my ZunSport grilles today, good quality and took about 25 minutes to fit. Not entirely sure I'm sold on them yet so going to drive around for a few days and make a call.
Ordered a new STi grille badge as I broke mine trying to remove it.
Ordered a new STi grille badge as I broke mine trying to remove it.
Last edited by 8ulldog; 14 July 2015 at 09:18 PM.
Scooby Regular
iTrader: (5)
What spark plugs are you guys using and any recommendations please? I will be servicing the car shortly and want to make sure everything is tip top before fitting a full 3" Miltek and mishimoto CAIK and Bob Rawle will be tweaking my map. Current spec is fully forged 330S with billet Owens 20g turbo. Thanks
Personally I think the black mesh would look better. The silver is a bit too bling!
Scooby Senior
I've got the black lower grille, suits my car. But think the blue can pull the chrome grilles off.. bling or no bling it looks quality.
I'd like to swap my main grille mesh for the zunsport in black... if anyone has one FS let me know