Cheers and sorry for the late reply.
Canon 400D and mostly a sigma 10-20 lens

 

They'll be a doddle to fit expect for the resonator box in the wing. You could leave that off if you put a cold air feed into the airbox another way - ducting from the front bumper etc

 

Love what you have done with yours mate. Its looking good. Im not that brave when it comes to modding. In case I **** it up or it looks cr@p. Its hard when you see some the stuff people have done on here.

 

Cheers bud, but it just takes a little bit of imagination, some care and help from the guys and gals on here - it's surprising what you can manage

 

Whats that to the bottom left of the cone filter ? Has someone tried to make a feed for it or is that there standard. Cant see what purpose it serves and cant see where it goes.

 

That is the resonator box in the wing, it connects to the cold air feed that runs of the bottom of the picture. With the airbox it fits onto that pipe.

I have replaced that with air ducting....

 

Camera must be broken - it all looks pink

Got any more under-bonnet piccys?

 

Hey guys I just noticed this thread and figured I would show my 02 WRX Bugeye from the US. I swapped it this past spring and put in a JDM EJ207 MY05 STi Spec C Type RA Engine, 6 speed and Brembo's. Essentially a fully converted Bugeye STi, which never existed in the US.



Here is a Picture of my Winter Wheels haha.

 

Love your winter wheels buddy. Different.

 

I bet they help locate it with some of the bad winters you have.

 

It is a WIP as I have a FMIC to fit so some of the hoses will be blue, maybe time for a change of colour direction

 

Yea it's not exactly hard to spot my car from across the parking lot lol.

 

Jon and Dave - you're both correct. The seats in that photo are simply the bugeye WRX bucket seats with Prodrive emblems ironed / stitched on.
I know that because they're the same as mine (sans Prodrive embroidery! )

My 01 Y WRX came with the airbag seats. However, they annoyed me immensely because they had so little side bolstering that if you took a corner too quick you ended up sliding off the seat and literally crashing into the door which I found VERY annoying.

I sold mine and bought a set of front seats off Domster from his X reg bugeye and find them more visually appealing and SO much more comfy and supportive than the airbag ones - just needed a few resistors soldered in to stop the airbag light coming on

 

Hey Kayen, what lights are those?, rather tastey.

 

They're STI headlights, the JDM ones also have HID fitted

 

It's like JonMc said they are the JDM STi HID headlights. I also baked the housings, so I could fully paint them Flat Black. I did this so I wouldn't have the chrome bezels in front of the Projector and Blinker lights.

 

Any ideas of suppliers/sources here in the uk?

 

Sorry I have no idea where you can buy any JDM STi HID setups at in the UK. Perhaps somebody on here from the UK can help you out with that.

 

You can only get the secondhand unless you import them yourself as far as I know. Ebay and the forums are the best bet, just keep your eyes open

You could always buy a UK set-up and add aftermarket HID kits. They are about £500+ from subaru

 

Yea I know for us in the US, they cost about $800-900 USD for used sets from Japan and go for $2,300 USD new from Subaru for the HID projectors...

 

I got a very nice set of the JDM HiD STi headlights 2nd hand with the smoked chrome inserts, would prefer the UK matt black ones tho.

Ricey

 

Why not bake yours and give them a coat of matt or satin black

 

nah, done that to the old OE lights, just would even think of trying that to the STi ones lol

Ricey

 

Did you have problems baking your OE lights?

It's a pretty straight forward process, time and patience. I have baked and painted over 5 sets between myself and friends lol. I painted my JDM projectors because I don't like the chrome bezels. Now it's just a clean flat black

 

NO problems, just don't fancy sticking the sti lights in an oven lol

 

some good lookin bug's there fella's, keep it up.
it has given me plenty of ideas of what to do with mine now

Bockett - lovin them wheels

 

Hi my name is Liz
only just seen this thread lol
heres my baby

 

Would love to post pic of mine but dont no how to pic is on cpu if any1 can tell me

 

im sorry peeps just cant work out how to do it but think if u look to the left hand side u might just see mine there fingers crossed lol

 

Have you got a photo hosting account like photobucket or flickr?

Not sure if you go to add reply then click the image icon at the top (Yellow looks like a hill and sun) if that works