Ken sorry to pic fault m8 but me old buddy Julian sti7 type uk has no figures posted......was it 296BHP and 274lb torque at 6100rpm?????

Thanx m8 ROB...

 

PS Rollers aren't low... they are realistic!!

Many times have I seen totally standard BRAND NEW cars run @ PowerStation to within a couple of BHP of their stated figure... for me that shows accuracy!

I mean, if you actually look at ALL of the figures from that day you will see that some cars made what they expected, some a little more... it's only ever the people who get LESS than they expected (or have been told by a 'tuner') that b!tch

I was actually there on the 6th and ran my white Evo 5 up (number 24 on the results list) and was well chuffed with 302bhp and 274lbf-ft considering the car only has a cat back exhaust and a HKS panel filter... maybe I should go to another dyno and get a 350bhp figure then?!

But, as is always said on almost ALL the forums over and over again... the figures only really mean anything if you use the SAME dyno to chart modifications and tuning to your own car... there is NO POINT comparing the figures from one Dyno to another as they will rarely be the same

Anyway, top one to Fuzz and his 386bhp run... not bad for a Uk car

Cheers
Jon

 

Rob edited list to include Julian. Well said Jon. my last car 99my turbo was pretty much standard and the result was 238 so they appear to be down to earth fiqures.
I just hope all those that went enjoyed it as much as me. 20 scoobies together is what its all about. not mines better than yours.
ken

 

I'll spec up the Datsun, and have the lot of ya next time...!

(Obviously, you'll all have gone by then so I can make up whatever power figures I like! LOL! )

Squizz.
(Getting bored with his Impreza... !!!!)

 

With regards to Interpro rollers, was there yesterday with a mate at a (dare I say it) Ford RS day, and an Engine Dyno'd Escort Cosworth @ proven 500BHP made 496BHP there! I would say that was pretty acurate Sounded mental too.

Ps, Thanks to Ken for organizing Saturday even tho I was disappointed with my results!

 

What have i started
I know Powerstation are very accurate not 100% but almost, thats why i'm pi$$ed off with my car and with all the warranty issues with it i don't want it no more hence the dealership is finding me a CTR as a replacement.

 

IMHO PS rolling road is damn near spot on for standard cars.

Last time I was there my old 118bhp decatted Elise made 124bhp

6bhp for a decat? Spot on mate!

 

Thanks ken for the day got 213/197 with center de cat and scorpion system just comfirms to my other half that I need to spend more money on a remap down/up pipe ect on my01 so I have proof now !!!!

 

Fuzz

Good figures for PS - think I got 383 and 312 I think.......... but thats before the latest mods on Jan 17th - shoud give me about 10-20bhp more on the current turbo!!!

Then I'd hope top hit 400bhp at PS

Steve

 

That's my aim too.... before I go internal.


Andy

 

well pleased with my results guys,03 wrx with just decat centre pipe and firestorm backbox 245bhp,was only expecting about 230bhp
cheers
jason

 

Thats is good mate, did'nt realise you were running just thought you were having an oil change.

 

yeh was always going to have a run but desperately needed oil first,what did you sort with your scoob?,i hear a ctr mentioned
cheers
jason

 

Yeah i'm off to look at one tomorrow, the very disapointing power results was the final straw for me so i nipped off to Subaru and shouted at them, fingers crossed.....

 

if yer wanting an upgrade then at least go & look at some proper meaty cars
Si (nudge nudge)

 

Fuzz

What Turbo are you running as you must be on boost lower than 1.5 bar on standard internals?

Is it the Bob Turbo?

If you can get this on standard internals not much point in spending the wad required to uprate the internals for the performance gains - max out at 500ish at PE = 440bhp at PS..........

rgds

Steve

 

Si, no i really fancy one of those fancy sporty MPV things

 

Fangoria,
Yes it's a "Bob" Turbo.

Boost wise, we are having a little difficulty keeping the boost down at the mo, wastegate duty cycle was 8% and it didn't want to go lower than 1.4 BAR.
Bob tried adjusting the actuator arm, without much sucess.

I would like to see how far the standard interals will go.

Edit to add : according to the defi's, the boost is creeping as far as 1.65 BAR when you cane the life out of it.


Andy

[Edited by Fuzz - 12/11/2003 10:13:36 AM]