3D Printed Fuel Filler Cap Holder
05 September 2018, 06:33 PM
#95
Cheers. That looks the same as the newage impreza one. Do you have a steel rule so that you measure the panel gap between the inner and outer skins at the bottom left of the bit where the label is? I'd be 99.99% sure it'll be 10mm ish so the std fuel cap holder I have will fit no worries.
16 October 2018, 10:15 PM
#102
Hello Bazil, I searched your posts to see if you were after suggestions as to what to 3D print, but gave up after 4 pages.
Anyway, if you are open to suggestions, one item of interest would be the classic sigma alarm fob. They break around the mounting points to the key ring and are hard to come by. As its only an outer casing that needs replacing which you can't buy, you have to buy the whole thing, which is now pretty expensive.
Anyway, just a suggestion, maybe start a thread to drum up some interest.
I personally don't need one right now, but I do have a broken one I could send you for a prototype.
I like all of your ideas so far.
Anyway, if you are open to suggestions, one item of interest would be the classic sigma alarm fob. They break around the mounting points to the key ring and are hard to come by. As its only an outer casing that needs replacing which you can't buy, you have to buy the whole thing, which is now pretty expensive.
Anyway, just a suggestion, maybe start a thread to drum up some interest.
I personally don't need one right now, but I do have a broken one I could send you for a prototype.
I like all of your ideas so far.
16 October 2018, 10:38 PM
#103
Hello Bazil, I searched your posts to see if you were after suggestions as to what to 3D print, but gave up after 4 pages.
Anyway, if you are open to suggestions, one item of interest would be the classic sigma alarm fob. They break around the mounting points to the key ring and are hard to come by. As its only an outer casing that needs replacing which you can't buy, you have to buy the whole thing, which is now pretty expensive.
Anyway, just a suggestion, maybe start a thread to drum up some interest.
I personally don't need one right now, but I do have a broken one I could send you for a prototype.
I like all of your ideas so far.
Anyway, if you are open to suggestions, one item of interest would be the classic sigma alarm fob. They break around the mounting points to the key ring and are hard to come by. As its only an outer casing that needs replacing which you can't buy, you have to buy the whole thing, which is now pretty expensive.
Anyway, just a suggestion, maybe start a thread to drum up some interest.
I personally don't need one right now, but I do have a broken one I could send you for a prototype.
I like all of your ideas so far.
Thanks for looking! Yeah I'm always open to suggestions, but don't have a specific thread for it. People have approached with ideas, some of which resulted in the for sale posts (the single din gauge mounting being one). I have some in the pipeline too, which I think are pretty awesome, will see where they end up. As for any ideas you have (or anyone else), drop me a PM and we can chat about it.
I've not personally seen the piece you're referring to, but pics and a broken one would certainly help, and if it's just a casing for a key fob then that should be doable. If you can send me it, I'm sure we can work out a good deal on a few pieces for when you do need it...
Cheers
Last edited by Bazil_SW; 16 October 2018 at 10:48 PM.
30 November 2018, 02:19 PM
#113
Still doing these Bazil? Could do with one for my Hatch STI
EDIT, I'm now wondering if the Hatch actually has one already fitted lol, don't have the car with me today so can't check !
EDIT, I'm now wondering if the Hatch actually has one already fitted lol, don't have the car with me today so can't check !
Last edited by TheOriginalAquapanther; 30 November 2018 at 02:23 PM.
