Geometry settings?
#1
Geometry settings?
Hi guys...
after my last thread on whether to get the camber/alignmet geometry setup done...I was wondering if I can just get Selecta Tyre (they have a Hunter kit)...to type in some general settings for fast road spec?
So...is this a good idea?
...has anyone got settings that would suit my Bugeye WRX 18" wheels (225/40/18)
...its just that I could do with not spending 150 quid and upwards for this....
or do I need to just bite the bullet and go to a Motorsport place?
after my last thread on whether to get the camber/alignmet geometry setup done...I was wondering if I can just get Selecta Tyre (they have a Hunter kit)...to type in some general settings for fast road spec?
So...is this a good idea?
...has anyone got settings that would suit my Bugeye WRX 18" wheels (225/40/18)
...its just that I could do with not spending 150 quid and upwards for this....
or do I need to just bite the bullet and go to a Motorsport place?
#2
Scooby Regular
iTrader: (9)
Join Date: Nov 2008
Location: South Wales
Posts: 1,292
Likes: 0
Received 0 Likes
on
0 Posts
I'd say bite the bullet..
But here's some settings for you:
This applies to a impreza sti from 2003-07
FRONT
left camber -1*00' tolerance 0*30'
right camber -1*00' tolerance 0*30'
cross camber tolerance 0*45'
left caster 2*30' tolerance 0*45'
right caster 2*30' tolerance 0*45'
total toe 0*12' tolerance 0*10'
left sai 15*22'
right sai 15*22'
REAR
camber -2*20' tolerance 0*30'
total toe 0*09' tolerance 0*10'
thrust angle tolerance 0*20'
These are the Prodrive settings, for the RB320 Geometry!
Road setting (Rear anti-roll bar in 2nd hole, nearest the end of the bar)
Values are read: minimum / preferred / maximum
Front Camber -1°20' / -1°15' / -1°10'
Front Toe-in (Total) 0°02' / 0°06' / 0°10'
Front Caster / 3°00' (Referential value) /
Rear Camber -2°15' / -1°30' / -0°54'(Std Subaru tolerance)
Rear Toe-in (Total) 0°02' / 0°60' / 0°10'
Thrust angle -0°01' / 0°00' / 0°01'
Track setting (Rear anti roll bar in 1st hole, nearest the mounting bush on the bar)
Values are read: preferred
Front Camber -1°30'(Maximum negative on adjustment)
Front Toe-in (Total) 0°06'
Front Caster 3°00' (Referential value)
Rear Camber -1°30'(Standard Subaru)
Rear Toe-in (Total) 0°06'
Thrust angle 0°00'
But here's some settings for you:
This applies to a impreza sti from 2003-07
FRONT
left camber -1*00' tolerance 0*30'
right camber -1*00' tolerance 0*30'
cross camber tolerance 0*45'
left caster 2*30' tolerance 0*45'
right caster 2*30' tolerance 0*45'
total toe 0*12' tolerance 0*10'
left sai 15*22'
right sai 15*22'
REAR
camber -2*20' tolerance 0*30'
total toe 0*09' tolerance 0*10'
thrust angle tolerance 0*20'
These are the Prodrive settings, for the RB320 Geometry!
Road setting (Rear anti-roll bar in 2nd hole, nearest the end of the bar)
Values are read: minimum / preferred / maximum
Front Camber -1°20' / -1°15' / -1°10'
Front Toe-in (Total) 0°02' / 0°06' / 0°10'
Front Caster / 3°00' (Referential value) /
Rear Camber -2°15' / -1°30' / -0°54'(Std Subaru tolerance)
Rear Toe-in (Total) 0°02' / 0°60' / 0°10'
Thrust angle -0°01' / 0°00' / 0°01'
Track setting (Rear anti roll bar in 1st hole, nearest the mounting bush on the bar)
Values are read: preferred
Front Camber -1°30'(Maximum negative on adjustment)
Front Toe-in (Total) 0°06'
Front Caster 3°00' (Referential value)
Rear Camber -1°30'(Standard Subaru)
Rear Toe-in (Total) 0°06'
Thrust angle 0°00'
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM