A few parts for sale removed from my 04 sti due to upgrades.

Top Mount Intercooler with oem sti silicone turbo pipe. Good used condition, a few bent fins as expected for age and in perfect working order £ SOLD collected or £ SOLD posted. (I can supply the mounting brackets f.o.c if your looking to fit to a classic).


2.5" Stainless Centre section Decat exhaust pipe, newage fitment, will fit standard oem or aftermarket 2.5" systems. Its 3 months old and covered less than 1000 miles so as such is in excellent condition £40 collected or £55 posted.

Mac 3 Port Boost Solenoid, Again its 3 months old and has covered less than 1000 miles so as such is in excellent condition, Works with oem or aftermarket ecu's and its the same solenoid "Harvey" used to supply and fit £30 collected or £35 posted.

Apexi AVCR 3 Port Boost Solenoid with its correct plug intact . Can also be used with most other electronic boost controllers and oem ecu's. Perfect working order £45 collected or £50 delivered.


Oem recirc valve newage fitment, excellent condition and in perfect working order as was removed from a 2006 hawk when almost new and has sat in a box until now. £....SOLD

Items can be collected from Redditch or Solihull
Cheers

Dubzy

 

Any pics of the Mac 3 port?

 

I will take some pics of the parts today but item is as new condition so will look the same as a new one

 

Pics added as requested and pm's replied

 

Are mounting brackets included for classic fit?

And will it clean up looks abit dirty bud?

 

Yes mate mounting brackets are included, one of the mounting rubber washers is a bit perished but i think u can reuse one of your old one's. The siliconey pipe and throttle body pipe are also included.

I usually give a good clean before taking pictures but didint have chance with doing other stuff. I will give it a clean and im sure it will come up ok

 

Just want my engine to to be nice and shinny

Don't mind giving it a clean but just wondered if it could be cleaned up easy enough.

 

I get ya, its not mint mate, its 10 years old and has the usual marks from where people have had tools etc on there. It looks like most ones ive seen to be fair and should clean up ok as i will do and put up a new picture once done. Would come up nice with a rattle can and bit of elbow grease

 

Very interested in this if you can deliver.........i'll send you a PM.

Its to go on a P1 - are there any mods needed?

Cheers

 

Top mount intercooler now sold

2.5" centre decat still available
Apexi 3 port solenoid still available
Mac 3 port boost solenoid still available

Will be going on ebay if not sold by next week so u may be able to grab a bargain...

 

The Apexi soloneid can it be run as a 2 port set up i noticed there isnt anything in the 3rd hole

 

Yes mate as when you upgrade to a 3 port the 3rd port has no connection and is left to vent to atmosphere. A 3 port is also fitted at time of mapping as needs tweaking to operate correctly.

 

So basicly just fit it as it is plug and play and leave the 3rd hole open to atmosphere to run as a 2 port?

 

You just alter the pipework slightly, 1 port goes directly to the actuator and 1 port goes to the nipple on the turbo and the third port is left open to vent. As stated your mapper will usually fit it and plumb it in during your mapping session. The apexi solenoid has the plug that fits directly to an apexi avcr so you would also need to piggy back two wires if your using it with the stock ecu in which case the mac 3 port that im selling will do the same job at a cheaper price.

 

Bump before hitting ebay......

 

Any pics of the decat pipe?

 

I dont at the moment mate but i will dig it out the garage on sturday and take some. Its only a few months old and as such is still in great condition

 

Pics as requested